Login

f4aii · (This post was last modified: 26-01-2018, 23:13 by f4aii.)

hello,

following 2 compilation errors for use with a 20X4 LCD on the RX PRO2 + V500_b002 with IDE 1.8.5 on MAC, I modified the code in the D_LCD tab
line 114: else if (UV_OutUnit! = 9 TX_Unit [UV_OutUnit] .UV! = 0) L_info = 5;
i wrote: else if (UV_OutUnit! = 9 && TX_Unit [UV_OutUnit] .UV! = 0) L_info = 5;

[Image: captur10.png]

now, it's OK

werk_ag · 27-01-2018, 02:00

(26-01-2018, 23:07)f4aii Wrote: following 2 compilation errors for use with a 20X4 LCD on the RX PRO2 + V500_b002...

I think you mean RX Pro2 PLUS + V500_b002

Thank you, indeed the error exists, and your solution is correct.
Somehow during some edition I deleted the && and haven't noticed it... the LCD rarely is used with te Pro2 PLUS.

f4aii · 27-01-2018, 08:00

I am preparing a weather station that will be in an uninhabited cabin at 2000m altitude and the TFT screen will be really useless.
As there is a wifi beam on the 10 km that separate us, a set TX, RX, UV, AQI will take place. As there is a lot of frost on this site, I will not put a cup anemometer, I will see later the design of an ultrasound model.

Here is why I use a LCD 20X4 which indeed must be very rare.
I wrote the wrong version of my platinum, it is a RX PRO2 PLUS V1.3, soft V500_b002.

f4aii · (This post was last modified: 30-01-2018, 21:57 by f4aii.)

same file, same hardware, i have an error on line 124:

Code:
#if (SR_OutUnit != 9)

    case 4:

      {

        lcd.setCursor(0, 3);

        lcd.print(F("Solar Rad: "));

        lcd.print(TX_Unit[SRUV_OutUnit].SolarRad);

        lcd.print(F(" Wm2"));

        if (UV_OutUnit != 9 && TX_Unit[UV_OutUnit].UV != 0) L_info = 5;

        else L_info = 1;

        break;

      }

i change for:

Code:
#if (SR_OutUnit != 9)

    case 4:

      {

        lcd.setCursor(0, 3);

        lcd.print(F("Solar Rad: "));

        lcd.print(TX_Unit[[b]SR[/b]_OutUnit].SolarRad);

        lcd.print(F(" Wm2"));

        if (UV_OutUnit != 9 && TX_Unit[UV_OutUnit].UV != 0) L_info = 5;

        else L_info = 1;

        break;

      }

It's OK for use with BMP280 and SHT31

But i have these errors if i select BME280 for pressure and int temp. Error on line 404: BME280 bme;

Code:
// --------------------------------------------------------------------------------------

//  WeatherDuino Pro2 PLUS RF Receiver - Version: 5.0 b002

//          Start of user configurable options 

// --------------------------------------------------------------------------------------

// If you need help about any of the user configurable settings, please first do a search

// at the WeatherDuino Pro2 support forum. If you don't find any relevant info, then post

// a new thread.

//

// --------------------------------------------------------------------------------------

//   Define Name and ID's for this weather station

// --------------------------------------------------------------------------------------

const String WeatherStation_Name = "Susville 3 test"; // This is important, put here your Weather Station name (don't use special chars, like accents)

#define Station_ID      0xA1    // Station_ID, use the same value in all TX units

#define Relay_ID        0xEE    // Relay_ID,   use the same value in all WD units

// --------------------------------------------------------------------------------------

//   Define your Weather Station location. Use decimal format for Latitude and Longitude

// --------------------------------------------------------------------------------------

#define LATITUDE      44.926    // Put here your Station latitude in degrees North (always use 3 decimal places)

#define LONGITUDE     5.777    // Put here your Station longitude in degrees - minus for West (always use 3 decimal places)

#define ELEVATION     900       // Put here your Station height above sea level in Meters (no decimal places)

// --------------------------------------------------------------------------------------

//   Define rules for Auto Summer Time Display, and clock adjustment

// --------------------------------------------------------------------------------------

#include <Timezone.h>

// Example for Australia Eastern Time Zone (Sydney, Melbourne) 

// TimeChangeRule aEDT = {"AEDT", First, Sun, Oct, 2, 660};    //UTC + 11 hours 

// TimeChangeRule aEST = {"AEST", First, Sun, Apr, 3, 600};    //UTC + 10 hours 

// Timezone myTZ(aEDT, aEST); 

TimeChangeRule PST = {"PST", Last, Sun, Mar, 1, 120};   //Portuguese Summer Time -  "UTC + 1" or GMT + 1

TimeChangeRule GMT = {"GMT", Last, Sun, Oct, 2, 60};    //Portuguese Winter Time -  "UTC + 0" or GMT 

Timezone myTZ(PST, GMT);

// --------------------------------------------------------------------------------------

//   Define Interface Language

// --------------------------------------------------------------------------------------

#include "_lang/fr_FR.h"      // Change the language code according to your preference. Keep "_lang/" and the ".h" at the end

                              // Currently available languages: en_GB, fr_FR, de_DE, pt_PT, es_ES, cs_CZ, nl_NL

// --------------------------------------------------------------------------------------

//   Define Roll Over Hour for Meteorological Day

// --------------------------------------------------------------------------------------

#define MeteoDay_HStart 0    // Use values from 0 to 23

// --------------------------------------------------------------------------------------

//   Define Display Backlight TimeOut

// --------------------------------------------------------------------------------------

const byte  BackLight_Timeout = 0;   // Timeout for display backlight in minutes (1 to 255). 0 = Always ON 

#define Use_BigClock             0    // Instead of turn off TFT backlight show a big clock screen. 0= No, 1= Yes

// --------------------------------------------------------------------------------------

//   Define data display units

// --------------------------------------------------------------------------------------

#define Date_Time_Format  0    // 0 for dd-mm-yyyy, 1 for yyyy/mm/dd

#define Temp_Display_Unit 0    // 0 for ºC, 1 for ºF

#define ATM_Display_Unit  0    // 0 for mBar, 1 for inHg

#define Rain_Display_Unit 0    // 0 for mm, 1 for inches

#define Wind_Display_Unit 0    // 0 for Km/h, 1 for mph, 2 for m/s, 3 for Knots

// --------------------------------------------------------------------------------------

//   Define the type of your Barometric Pressure Sensor

// --------------------------------------------------------------------------------------

#define Barometric_Sensor  0   // 0= BME280, 1= BMP280 2= BMP085 / BMP180

// --------------------------------------------------------------------------------------

//   Define the type of your inside Temperature / Humidity Sensor

// --------------------------------------------------------------------------------------

#define InsideTH_Sensor   0   // 0= BME280, 1= HTU21D, 2= SHT21, 3= SHT31

// --------------------------------------------------------------------------------------

//   Fine adjusts for Inside Temperature and Barometer

// --------------------------------------------------------------------------------------

const int   TemperaturaInt_offset =   -13;   // Inside Temperature Fine Adjust in Tenths of Degree (-4 = -0,4ºC) 

const float pressure_offset       =   0;   // Pressure Fine Adjust in mB

// --------------------------------------------------------------------------------------

//   Define the type of your outside Temperature / Humidity Sensor

// --------------------------------------------------------------------------------------

#define MainOutTH_Sensor 0   // 0 for sensor type SHT31, SHT21 or HTU21D, 1 for sensor type SHT1x or DHT22 

// --------------------------------------------------------------------------------------

//   Define Wind Speed and Wind Gust resolution

// --------------------------------------------------------------------------------------

// This setting only have effect when the software is used in Davis VP emulation mode

#define VP2_WindRes     2    // If set to 2, set Cumulus Wind Speed and Wind Gust multipliers to 0.448. Wind Resolution 0.72 Km/h

                             // If set to 1, set Cumulus Wind Speed and Wind Gust multipliers to 0.224. Wind Resolution 0.36 Km/h

                             // WARNING !!! Setting this variable to 1 allows a better wind speed and gust resolution,

                             // but also limits both of them, to a maximum reading of just 91.8 Km/h

                             // If set to 0, system uses Standard Davis wind resolution (1 mph or 0.1mph with LOOP2).

                             // Weather Display users should set this option to 0 - Standard Davis wind resolution   

// --------------------------------------------------------------------------------------

//   Define use of Wind Gust Spike prevention routines (mostly for FO anemometers)

// --------------------------------------------------------------------------------------

#define WindSpikeControl 1   // 0= Disable, 1= Enable

// --------------------------------------------------------------------------------------

//   Define the source of your main outside sensors

// --------------------------------------------------------------------------------------

// ---- If you are using just one TX board, the source for all items should be equal to your single TX Unit ID (most likely zero).

// ---- Define the source of your main Temperature / Humidity sensor

#define TH_OutUnit       0   // 0= Temp/Hum sensor connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Temp / Hum

// ---- Define the source of your Main Wind sensor

#define WIND_OutUnit     0   // 0= Wind instruments connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Wind Speed & Dir

// ---- Define the source of your main Rain Gauge

#define RAIN_OutUnit     0   // 0= Rain Gauge connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Rain Gauge

// ---- Define the source of your main Solar Radiation sensor

#define SR_OutUnit       0   // 0= Solar Radiation sensor connected to TX_Unit 0, 1= for TX_Unit1, ..., 9 for not used

// ---- Define the source of your main UV sensor

#define UV_OutUnit       0  // 0= UV sensor connected to TX_Unit 0, 1= for TX_Unit1, ..., 9 for not used

// --------------------------------------------------------------------------------------

//   Define the type of your Solar Radiation device

// --------------------------------------------------------------------------------------

#define Solar_Sensor     1   // 1= Solar Cell "Pyranometer", 2= Apogee SP-110 Pyranometer, 3= Reserved, 4= Apogee SQ-110: Photosynthetically Active Radiation Sensor

                             // ---- Support for sensor type 4 is experimental (type 4 is a PAR sensor)

// --------------------------------------------------------------------------------------

//   Define the type of your UV device

// --------------------------------------------------------------------------------------

#define UV_Sensor        1   // 1= UVM-30A, 2= VEML6075, 3= Reserved 

#define UV_Transmission 65   // UV Transmission percentage of UV sensor cover material. 

// --------------------------------------------------------------------------------------

//   Extra Sensors Settings and Mapping

// --------------------------------------------------------------------------------------

// ---- Define the source and sensor type (number) for each of the seven extra sensors, insert 9 if not used.

//      Sensors SHT31, SHT21 or HTU21D are type 0, sensors SHT1x or DHT22 are type 1

// 

// ---- Source 0 means TX unit0, 1 means TX unit1... 

// ---- Source 6 (Reserved)

// ---- Source 7 is for BIOS Sensor (Only Temperature is shown)

// ---- Source 8 is for Air Quality Monitor. 0= Temperature/Humidity, 1= Dust Density/AQI

// ---- (AQI sensors can be mapped to any position, but should be mapped in sequence, Temperature/Humidity always first)

//

// ---- First field = Sensor source, Second field = Sensor type (0 or 1 for TX units) 

// ---- Example:

// ----                          ES0   ES1   ES2   ES3   ES4   ES5   ES6     

//#define ExtraSensors_Source { {0,1},{1,1},{9,9},{6,3},{9,9},{8,0},{8,1} }

//               {0,0} - First extra sensor (ES0), will be sensor 0 from TX unit0

//               {0,1} - Second extra sensor (ES1), will be sensor 1 from TX unit0

//               {1,0} - Third extra sensor (ES2), will be sensor 0 from TX unit1

//               {9,9} - Fourth extra sensor (ES3), not used - not mapped

//               {9,9} - Fifth extra sensor (ES4), not use - not mapped

//               {8,0} - Sixth extra sensor (ES5), will be Temperature / Humidity from the Air Quality Monitor

//               {8,1} - Seventh extra sensor (ES6), will be Dust Density / AQI index from the Air Quality Monitor 

//

//-----                        ES0   ES1   ES2   ES3   ES4   ES5   ES6     

#define ExtraSensors_Source { {0,0},{0,1},{9,9},{9,9},{9,9},{8,0},{8,1} }

// ---- Define personalized names for each Extra sensor. Attention, 8 chars maximum

// ---- There is no need to define a name for the Extra Sensor mapped to the Dust Density / AQI index data

//                   Max. Size  [--------] 

const char ESname_1[] PROGMEM = "dehors";           // 8 chars max

const char ESname_2[] PROGMEM = "boitier";           // 8 chars max 

const char ESname_3[] PROGMEM = "-";           // 8 chars max

const char ESname_4[] PROGMEM = "-";           // 8 chars max

const char ESname_5[] PROGMEM = "-";           // 8 chars max

const char ESname_6[] PROGMEM = "AQM";     // 8 chars max

const char ESname_7[] PROGMEM = "AQM";           // 8 chars max

// --------------------------------------------------------------------------------------

//   BIOS soil moisture sensor settings

// --------------------------------------------------------------------------------------

// ---- Please use the included BIOS_ID_Scanner sketch to find you BIOS Device ID

#define BiosSensor_ID 0   // Device ID in HEX format, or 0 not used

// --------------------------------------------------------------------------------------

//   Soil / Leaf Interface Settings and Sensors Mapping

//   (The mapping logic is the same than used with the Extra Sensors)

// --------------------------------------------------------------------------------------

// 0 = Soil Leaf Interface not used

// 1 = Soil Leaf Interface connected to a TX unit

#define SoilLeaf_Interface  0   // 0, 1, 

// ---- For Soil & Leaf data from SoilLeaf_Interface wired to a TX unit, use TX Unit number as source 

// ---- For BIOS Soil Temp / Moisture use 7 as source

// ---- To disable use 9 in both fields

//                                 S1    S2    S3    S4

#define SoilTempSensors_Source  { {9,9},{9,9},{9,9},{9,9} }

#define LeafTempSensors_Source  { {9,9},{9,9},{9,9},{9,9} }

#define SoilMoistSensors_Source { {9,9},{9,9},{9,9},{9,9} }

#define LeafWetSensors_Source   { {9,9},{9,9},{9,9},{9,9} }

// ---- Define personalized names for each Soil and Leaf sensor. Attention, 8 chars maximum

//              Soil Max. Size  [--------] 

const char SSname_1[] PROGMEM = "-";            // 8 chars max

const char SSname_2[] PROGMEM = "-";            // 8 chars max 

const char SSname_3[] PROGMEM = "-";            // 8 chars max

const char SSname_4[] PROGMEM = "-";            // 8 chars max

//              Leaf Max. Size  [--------] 

const char LSname_1[] PROGMEM = "1";            // 8 chars max

const char LSname_2[] PROGMEM = "2";            // 8 chars max

const char LSname_3[] PROGMEM = "3";            // 8 chars max

const char LSname_4[] PROGMEM = "4";            // 8 chars max

// Define VWC calculation method

// Method 1 applies only for VH400 soil moisture sensor

//

// METHOD 1 - Conversion from voltage to VWC (volumetric water content) is done using the piecewise regressions provided by the manufacturer 

// at http://www.vegetronix.com/Products/VH400/VH400-Piecewise-Curve.phtml 

//

// METHOD 2 - Used for any sensor which have a linear output between voltage and VWC (0V=0VWC, maxV=100VWC) .

#define VWC_CalcMethod 1

// Max and Min output voltage of the analog sensors connected to Soil / Leaf Interface

// Default value for Decagon Devices LWS Leaf Wetness Sensor (3.3V power): Max. Output Voltage - 1395mV (max wetness), Min Output Voltage - 530mV (dry)

//                                                  ADC1  ADC2  ADC3  ADC4  

const uint16_t AnalogSensor_MaxVoltOut[4]   = { 3000, 1395, 5000, 5000 };    // Values in miliVolts

const uint16_t AnalogSensor_MinVoltOut[4]   = {    0,  530,    0,    0 };

// --------------------------------------------------------------------------------------

//   Broadacasting settings for Wireless Display Units

// --------------------------------------------------------------------------------------

#define Relay_Data       1   // 0= Disables Data Relay, 1= Enables Data Relay

// --------------------------------------------------------------------------------------

//   Davis compatible Data Logger Settings

// --------------------------------------------------------------------------------------

#define Logger_Enable    1   // 0= Disable 1= Enable

byte ARCHIVE_PERIOD  =   5;  // Default Archive Period in Minutes (Usable values: 1, 5, 10, 15, 30)

// --------------------------------------------------------------------------------------

//   Define type of your Weather Software 

// --------------------------------------------------------------------------------------

#define WeatherSoft      0   // 0= CumulusMX, 1= Any other (Cumulus 1, WeewX, Weather Display, etc.)

// --------------------------------------------------------------------------------------

//   Easyweather format data Output 

// --------------------------------------------------------------------------------------

#define Easyweather_Out  0   // 0= Disable (defaut) 1= Enable

// --------------------------------------------------------------------------------------

//   Internet Settings 

// --------------------------------------------------------------------------------------

#define Enable_Internet     1                       // 1= Enable Internet connection, 0= Disable

// ---- NTP Settings ----

#define Enable_NTP          1                       // 1= Enable Sync time with NTP servers, 0= Disable

// NTP Servers: 

#define timeServer "pool.ntp.org"

//#define timeServer "time.nist.gov"                 // ntp1.nl.net NTP server

//#define timeServer "80.96.196.58"                  // timp.mcsi.ro

//#define timeServer "193.79.237.14"                 // ntp1.nl.net NTP server

// ---- Weather Wunderground Settings ----

#define Enable_WUupload     1                       // 1= Enable upload to Wunderground, 0= Disable

#define WUupload_period     3                        // Period in minutes between uploads to WU (Should be >= 3 minutes, if less defaults to 4 minutes) 

#define WUupload_InTemp     1                        // 1= Enable upload of Inside Temperature / Humidity, 0= Disable

// ---- Air Quality Monitor - Upload to ThingSpeak Settings ----

#define Enable_AQMtoThingSpeak   1                   // 1= Enable, 0= Disable

// ---- Web Server Settings ----

#define Enable_WebServer          1                  // 1= Enable 0= Disable

#define WebServer_port           80                  // WebServer port (default 80) 

// --------------------------------------------------------------------------------------

//   Enable / Disable GPIO routines - General Purpose Input / Output ports

// --------------------------------------------------------------------------------------

#define UseGPIO  0   // 0=Disable, 1= Enable

// --------------------------------------------------------------------------------------

//   Define display order of data screens on the TFT

//   Use sequentially numbers from 1 to 4. Use 9 to prevent a particular data screen to be shown

// --------------------------------------------------------------------------------------

#define ExtraSensors_Data 3

#define SoilLeaf_Data     4

#define AirQuality_Data   1

#define TXinfo_Data       2

// --------------------------------------------------------------------------------------

//   Test Mode : Never run a live system in test mode 

// --------------------------------------------------------------------------------------

#define TestMode    false    // false= Normal working mode, true= Test mode only (no logger, no usb connection)

/*************************************************************************************

     Hardware Settings 

*************************************************************************************/

// --------------------------------------------------------------------------------------

//   Define PCB Version Number

// --------------------------------------------------------------------------------------

//                              Take particular attention to this setting.

//                              Your system may not work properly if you define a wrong pcb version number.

//                              In case of doubt check what is printed in your pcb.

#define Board_Version   13   // PCB version number, without the decimal point Ex: 1.3 = 13 (integer number)

// --------------------------------------------------------------------------------------

//   Define your Display type

// --------------------------------------------------------------------------------------

#define DisplayType     1    // 1= LCD 20x4, 3= TFT 320x240 ILI9341

// --------------------------------------------------------------------------------------

//   Define LCD I2C address 

// --------------------------------------------------------------------------------------

// Only change this if your LCD don't display any data. I2C_Scanner utility may help you to find the address of your LCD display

// Default address will work most of the times!

#define LCD_I2C_Address     0x39   

// --------------------------------------------------------------------------------------

//   SHT31 I2C Address - Default address will work most of the times!

// --------------------------------------------------------------------------------------

#define SHT31_address       0x44       // Default value is 0x44, but it can be changed to 0x45

// --------------------------------------------------------------------------------------

//   Presure Sensor Address (no need to change)

// --------------------------------------------------------------------------------------

//#define BMP085_ADDRESS    0x77       // I2C address of BMP085 or BMP180

// --------------------------------------------------------------------------------------

//   Debug helper 

// --------------------------------------------------------------------------------------

//#define PRINT_DEBUG_NTP_UPDATE    // Print to serial monitor messages related to sync time with NTP server

//#define PRINT_DEBUG_WU_UPLOAD     // Print to serial monitor messages related to Weather Underground upload.

//#define PRINT_DEBUG_TS_UPLOAD

//#define PRINT_DEBUG_VCHECK

//#define PRINT_DEBUG_TCP_SERVER

//#define PRINT_DEBUG_AURIOL

//#define PRINT_DEBUG_BIOS

// ---------------------------------------------------------------------------------------------------

//     End of user configurable options

// ---------------------------------------------------------------------------------------------------

Arduino : 1.8.5 (Windows 7), Carte : "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)"
WeatherDuinoPro2Plus_RX_v500_b002:404: error: cannot declare variable 'bme' to be of abstract type 'BME280'
BME280 bme;
^
In file included from C:\Users\jch\Desktop\WeatherDuino_Pro2_PLUS\v5.0\software\RX software\WeatherDuinoPro2Plus_RX_v500_b002\WeatherDuinoPro2Plus_RX_v500_b002.ino:53:0:
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:52:7: note: because the following virtual functions are pure within 'BME280':
class BME280{
^
In file included from C:\Users\jch\Desktop\WeatherDuino_Pro2_PLUS\v5.0\software\RX software\WeatherDuinoPro2Plus_RX_v500_b002\WeatherDuinoPro2Plus_RX_v500_b002.ino:53:0:
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:66:16: note: virtual void BME280::WriteRegister(uint8_t, uint8_t)

virtual void WriteRegister(uint8_t addr, uint8_t data)=0;
^
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:69:16: note: virtual bool BME280::ReadTrim()
virtual bool ReadTrim()=0;
^
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:72:16: note: virtual bool BME280::ReadData(int32_t*)
virtual bool ReadData(int32_t data[8])=0;
^
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:89:16: note: virtual bool BME280::begin()
virtual bool begin()=0;
^
C:\Users\jch\Desktop\WeatherDuino_Pro2_PLUS\v5.0\software\RX software\WeatherDuinoPro2Plus_RX_v500_b002\Routines.ino: In function 'void read_InsideTH_Sensor()':
Routines:330: error: no matching function for call to 'BME280::ReadData(float&, float&, float&, bool, bool)'
bme.ReadData(pres, temp, humd, true, true); // Parameters: (float& pressure, float& temp, float& humidity, bool hPa = true, bool celsius = false)
^
C:\Users\jch\Desktop\WeatherDuino_Pro2_PLUS\v5.0\software\RX software\WeatherDuinoPro2Plus_RX_v500_b002\Routines.ino:330:44: note: candidate is:
In file included from C:\Users\jch\Desktop\WeatherDuino_Pro2_PLUS\v5.0\software\RX software\WeatherDuinoPro2Plus_RX_v500_b002\WeatherDuinoPro2Plus_RX_v500_b002.ino:53:0:
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:72:16: note: virtual bool BME280::ReadData(int32_t*)
virtual bool ReadData(int32_t data[8])=0;
^
C:\Users\jch\Documents\Arduino\libraries\libraries\BME280\src/BME280.h:72:16: note: candidate expects 1 argument, 5 provided

exit status 1
cannot declare variable 'bme' to be of abstract type 'BME280'

werk_ag · 31-01-2018, 01:50

This is from the download page:

IMPORTANT:
Compile with Arduino IDE 1.8.3 or newer
Always compile using only the provided libraries.

From the error messages I see that you are using an BME library which isn't compatible. Try using the BME library suplied with the software package, and the code will compile fine (I'm using a BME280 myself).

Regards

f4aii · 01-02-2018, 07:27

I made the mistake of using my desktop PC that contains other libraries in addition to weatherduino. IDE chooses the wrong library.

I still have the error message for line 124 in the D_LCD tab,
must be fixed:
lcd.print(TX_Unit [SRUV_OutUnit] .SolarRad);
and put:
lcd.print (TX_Unit [UV_OutUnit] .SolarRad);
I have no other errors now.

Too bad the error messages are so little understandable for beginners like me.
Thanks for your help.

werk_ag · 02-02-2018, 02:33

Hi,

Thank you for spotting this to me. It will be fixed on next software release.
However please note that the fix for line 124 should be:

Code:
lcd.print(TX_Unit[SR_OutUnit].SolarRad);

and not

Code:
lcd.print (TX_Unit [UV_OutUnit] .SolarRad);

which only works when the source for Solar Radiation data is the same than UV data (which happens in most of the cases).

f4aii · 03-02-2018, 09:30

I do not understand much about codes, I modified by deduction.
Right now, I am changing the code for my brother who is color-blind, he only sees white, gray, black and yellow. I change the color of the dots around the clock so that he can tell me if the weatherduino is connected or not. Nothing complicated to do.
thank you

werk_ag · 04-02-2018, 05:54

(03-02-2018, 09:30)f4aii Wrote: I do not understand much about codes, I modified by deduction.

However, you already have helped me to find some bugs... Smile

(03-02-2018, 09:30)f4aii Wrote: Right now, I am changing the code for my brother who is color-blind, he only sees white, gray, black and yellow. I change the color of the dots around the clock so that he can tell me if the weatherduino is connected or not. Nothing complicated to do.
thank you

If I could help with anything on this matter, please let me know, I will be glad to help to make the system usable for your brother.

Login
Username:
Password:	Lost Password?
	Remember me