This forum uses cookies
This forum makes use of cookies to store your login information if you are registered, and your last visit if you are not. Cookies are small text documents stored on your computer; the cookies set by this forum can only be used on this website and pose no security risk. Cookies on this forum also track the specific topics you have read and when you last read them. Please confirm whether you accept or reject these cookies being set.

A cookie will be stored in your browser regardless of choice to prevent you being asked this question again. You will be able to change your cookie settings at any time using the link in the footer.

Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
AQM II dust sensor trouble
#1
I have my AQM up and running with a Display, MH-Z19B SDS011 and SHT31 temp sensor.

Using software WeatherDuino_AQM_ESP8266_ASK_v120_b002

I am getting sensible readings back from the temp sensor and Co2 sensor ok, but the SDS011 gives the following response.


Code:
09:45:03.055 -> Waking up the dust sensor...
09:45:03.055 -> Reading will be done 40s later.
09:45:03.055 -> 
09:45:43.034 -> Reading the dust sensor...
09:45:43.034 -> 
09:45:44.036 -> EC,8A,FE,3F,1,0,0,0,94,6C,
09:45:44.036 -> Calculate crc: 3E
09:45:44.070 ->  Response crc: 94
09:45:44.070 -> 
09:45:44.070 -> Wrong reply from SDS011 sensor!


There isn't much to show relevant to the dust sensor in the config options other than..


Code:
// --------------------------------------------------------------------------------------
//   Define type of PM sensor
// --------------------------------------------------------------------------------------
#define DUSTSENSOR_TYPE  1    // 0= PMS7003, 1= nova SDS011

I have tested the SDS011 with the manufacturers software and the USB to COM port adaptor that came with it and it works fine, so I know the sensor is ok.

I assume that I need to wire it up as follows.

AQM     SDS011
SET      TXD
TX        RXD
GND     GND
5V        5V

Grateful for any pointers!

Thanks Andy
Reply
#2
(18-04-2019, 10:39)atbukc Wrote: I have my AQM up and running with a Display, MH-Z19B SDS011 and SHT31 temp sensor.

I have tested the SDS011 with the manufacturers software and the USB to COM port adaptor that came with it and it works fine, so I know the sensor is ok.

I assume that I need to wire it up as follows.

AQM     SDS011
SET      TXD
TX        RXD
GND     GND
5V        5V

Hello Andy,

I don't have SDS011, but I'd try to switch the wires TX and SET ...
Good luck!
Best Regards
Zdenek

[Image: banner.php]
My outdoor AQM-I: here
Reply
#3
(18-04-2019, 14:16)hornychz Wrote:
(18-04-2019, 10:39)atbukc Wrote: I have my AQM up and running with a Display, MH-Z19B SDS011 and SHT31 temp sensor.

I have tested the SDS011 with the manufacturers software and the USB to COM port adaptor that came with it and it works fine, so I know the sensor is ok.

I assume that I need to wire it up as follows.

AQM     SDS011
SET      TXD
TX        RXD
GND     GND
5V        5V

Hello Andy,

I don't have SDS011, but I'd try to switch the wires TX and SET ...
Good luck!
Perfect, all working fine now..

Thanks Andy.
Reply




Users browsing this thread: 1 Guest(s)