04-07-2017, 21:21
Hi everyone
Sorry for the delay in getting these posted.
Here are the images of my PCB -
This is the config code for the TX unit
Here is the code for the RX unit
I hope the photos are detailed enough.
Thanks
Chris
Sorry for the delay in getting these posted.
Here are the images of my PCB -
This is the config code for the TX unit
Code:
// --------------------------------------------------------------------------------------
// WeatherDuino Pro2 Universal TX - Version: 3.1 b002
// Start of user configurable options
// --------------------------------------------------------------------------------------
// --------------------------------------------------------------------------------------
// Define ID and TX unit number
// --------------------------------------------------------------------------------------
#define StationID 0xA1 // Must be equal to your RX Unit (Value from 0x00 to 0xFF)
#define UnitID 0 // If you use only one TX unit define it as UnitID = 0
// For a second TX unit, define it as UnitID = 1
// --------------------------------------------------------------------------------------
// Define type of Temperature / Humidity sensor used as Sensor 0 and / or Sensor 1
// --------------------------------------------------------------------------------------
#define TH_Sensor0 1 // [SENSOR 0] - 0 for SHT2x sensor, 1 for SHT31 sensor, 2 for HTU21 sensor, 9 for Not Used
#define TH_Sensor1 9 // [SENSOR 1] - 0 for SHT1x sensor, 1 for DHT22 sensor, 9 for Not Used
// --------------------------------------------------------------------------------------
// Define which Temp / Hum sensor controls the fan, and threshold values
// --------------------------------------------------------------------------------------
#define FanControlSensor 0 // 0 for Sensor 0, 1 for Sensor 1 (which sensor is used to control the RS Fan)
#define fanOn_HiTemp 38 // RS Fan turn on when outside temperature is >= than this value (ºC)
#define fanOn_LowTemp 2 // RS Fan turn on when outside temperature is <= than this value (ºC)
#define fanOn_LowWind 1 // RS Fan turn on when Wind Average is <= than this value (m/s)
// --------------------------------------------------------------------------------------
// Define type of Wind Speed sensor. See below for allowed types
// --------------------------------------------------------------------------------------
/*
--- Fine Offset Anemometers ---
Use 1O for standard FO anemometers
Use 11 for FO anemometer modified with 1 hall effect sensor
--- Inspeed Anemometers ---
Use 20 for Inspeed Vortex, digital 8 pulse revolution anemometer
Use 21 for Inspeed Vortex, hall efect sensor
Use 22 for Inspeed Vortex, read switch sensor
--- Davis Anemometers ---
Use 30 for Davis 6410, 7911 anemometer
--- Novalynx Anemometers ---
Use 40 for Novalynx, model 200-WS-02F
--- Environmental Measurements Limited ---
Use 50 for EML, model WSD1
--- Didcot Instrument Company ---
Use 60 for DIDCOT, model DWR205
*/
#define WSpeedSensor_Type 30 // SEE INFO ABOVE!!!
// --------------------------------------------------------------------------------------
// Define type of Wind Direction sensor
// --------------------------------------------------------------------------------------
/*
--- Fine Offset Wind Vane ---
Use 1O for standard FO wind vane
--- Inspeed Wind Vane ---
Use 20 for Inspeed E-Vane 2
--- Davis Wind Vane ---
Use 30 for Davis 6410 wind vane
--- Novalynx Wind Vane
Use 40 for Novalynx, model 200-WS-02F
--- Environmental Measurements Limited Wind Vane ---
Use 50 for EML, model model WSD1
--- Didcot Instrument Company ---
Use 60 for DIDCOT, model DWD205
*/
#define WDirSensor_Type 30 // SEE INFO ABOVE!!!
// --------------------------------------------------------------------------------------
// Inspeed Vane Calibration
// Calibration values for Inspeed E-Vane 2
// --------------------------------------------------------------------------------------
#define WDir_min 60
#define WDir_max 990
#define WDir_offs 0
// --------------------------------------------------------------------------------------
// Define Rain Gauge tip boucket value (mm)
// --------------------------------------------------------------------------------------
/*
Use 0.280 for standard FineOfset rain gauges (Datasheet value = 0.2794)
Use 0.200 for standard metric Davis rain gauges
Use 0.254 for standard imperial Davis rain gauges
*/
#define COLLECTOR_TYPE 0.280 // Please note: Values must be in metric units. Max. resolution: 3 decimal digits
// --------------------------------------------------------------------------------------
// Define type of UV Sensor
// --------------------------------------------------------------------------------------
#define UV_Sensor 9 // 0= UVM-30A, 1= VEML6075, 9= Not used
// --------------------------------------------------------------------------------------
// Soil / Leaf Interface Enable Disable
// --------------------------------------------------------------------------------------
#define SoilLeaf_Interface 0 // 0 = Soil Leaf Interface not used, 1 = Enable Soil Leaf Interface
#define Number_AnalogSensors 2 // Up to 4 analog sensors
// --------------------------------------------------------------------------------------
// Define which data this unit will send. 0 = Not send this data, 1= Send this data
// --------------------------------------------------------------------------------------
#define ID0 1 // Temp/Hum Data
#define ID1 0 // Not Used
#define ID2 1 // Wind data
#define ID3 0 // Rain data
#define ID4 0 // SolRad / UV data
#define ID5 1 // Hardware Status - System Temp, Battery Voltage etc
#define ID7 0 // Send Soil & Leaf Temperature Data
#define ID9 0 // Send Soil & Leaf Moisture / Wetness Data
// --------------------------------------------------------------------------------------
// Hardware settings
// --------------------------------------------------------------------------------------
// SHT31 I2c Address
// Default address will work most of the times!
#define SHT31_address 0x44 // Default value is 0x44, but it can be changed to 0x45
// --------------------------------------------------------------------------------------
// Debug
// --------------------------------------------------------------------------------------
#define Debug_Enable true
#define DebugID0 true
#define DebugID2 true
#define DebugID3 false
#define DebugID4 false
#define DebugID5 true
#define Easyweather_Test false
#define Debug_SLinterface true
// ---------------------------------------------------------------------------------------------------
// End of user configurable options
// ---------------------------------------------------------------------------------------------------Here is the code for the RX unit
Code:
// --------------------------------------------------------------------------------------
// WeatherDuino Pro2 RF Receiver - Version: 2.10 b002
// User configurable options
// --------------------------------------------------------------------------------------
// --------------------------------------------------------------------------------------
// Define ID's for this weather station
// --------------------------------------------------------------------------------------
#define Station_ID 0xA1 // Station_ID, use the same value in all TX units
#define Relay_ID 0xA3 // Relay_ID, use the same value in all WD units
// --------------------------------------------------------------------------------------
// Define your Weather Station location
// --------------------------------------------------------------------------------------
#define LATITUDE 0 // Put here your Station latitude in tenths of degrees North
#define LONGITUDE 0 // Put here your Station longitude in tenths of degrees (minus for West)
#define ELEVATION 28 // Put here your Station height above sea level in Meters
// --------------------------------------------------------------------------------------
// Define Roll Over Hour for Meteorological Day
// --------------------------------------------------------------------------------------
#define MeteoDay_HStart 0 // Use values from 0 to 23
// --------------------------------------------------------------------------------------
// Define Software Operation Mode
// --------------------------------------------------------------------------------------
#define Work_Mode 0 // Mode 0= Davis VP2 Emulation Mode, Mode 1= EasyWeather Mode
// --------------------------------------------------------------------------------------
// Define your Display type
// --------------------------------------------------------------------------------------
#define DisplayType 0 // 0= LCD 20x4, 2= LCD 16x2
// --------------------------------------------------------------------------------------
// Define Display Backlight TimeOut
// --------------------------------------------------------------------------------------
// ---- For old RX boards, version <= 3.01 always set this value to 0
const byte BackLight_Timeout = 30; // Timeout for display backlight in minutes (1 to 255). 0 = Always ON
// --------------------------------------------------------------------------------------
// Define data display units
// --------------------------------------------------------------------------------------
#define Date_Time_Format 0 // 0 for dd-mm-yyyy, 1 for yyyy/mm/dd
#define Temp_Display_Unit 0 // 0 for ºC, 1 for ºF
#define ATM_Display_Unit 0 // 0 for mBar, 1 for inHg
#define Rain_Display_Unit 0 // 0 for mm (no other options)
#define Wind_Display_Unit 1 // 0 for Km/h, 1 for mph, 2 for m/s, 3 for Knots
// --------------------------------------------------------------------------------------
// Fine adjusts for Inside Temperature and Barometer
// --------------------------------------------------------------------------------------
const int TemperaturaInt_offset = 0; // Inside Temperature Fine Adjust in Tenths of Degree (-4 = -0,4ºC)
const float SeaLevel_ATM_offset = 0; // Pressure Fine Adjust in mB
// --------------------------------------------------------------------------------------
// Define Wind Speed and Wind Gust resolution
// --------------------------------------------------------------------------------------
#define VP2_WindRes 2 // If set to 2, set Cumulus Wind Speed and Wind Gust multipliers to 0.448. Wind Resolution 0.72 Km/h (limite 183.6 Km/h)
// If set to 1, set Cumulus Wind Speed and Wind Gust multipliers to 0.224. Wind Resolution 0.36 Km/h (limite 91.8 Km/h)
// WARNING !!! Setting this variable to 1 allows a better wind speed and gust resolution,
// but also limits both of them, to a maximum reading of just 91.8 Km/h
// This setting only have effect when the software is used in Davis VP2 emulation mode
// If set to 0, system uses Standard Davis 1 mph wind resolution (limite 241 Km/h).
// --------------------------------------------------------------------------------------
// Define use of Wind Gust Spike prevention routines
// --------------------------------------------------------------------------------------
#define WindSpikeControl 1 // 0= Disable, 1= Enable
// --------------------------------------------------------------------------------------
// Define the type of your inside Temperature / Humidity Sensor
// * Auriol users can't use the SHT31 sensor
// --------------------------------------------------------------------------------------
#define InsideTH_Sensor 1 // 0= DHT22, 1= HTU21D, 2= SHT21, 3*= SHT31
// --------------------------------------------------------------------------------------
// Define the type of your outside Temperature / Humidity Sensor
// --------------------------------------------------------------------------------------
#define MainOutTH_Sensor 0 // 0 for sensor type SHT31, SHT2x or HTU21D, 1 for sensor type SHT1x or DHT22 (Always 0 when working with Auriol and clones)
// --------------------------------------------------------------------------------------
// Define the source of your main outside sensors
// --------------------------------------------------------------------------------------
// ---- If you have all the sensors connected to only one TX board, always select Unit 0 as source
// ---- Define the source of your main Temperature / Humidity sensor
#define TH_OutUnit 0 // 0 for Temp/Hum sensor connected to TX_Unit 0, 1 for Temp/Hum sensor connected to TX_Unit 1, 3 for Auriol RF Wind Speed
// ---- Define the source of your Main Wind sensor
#define WIND_OutUnit 0 // 0 for Wind instruments connected to TX_Unit 0, 1 for TX_Unit 1, 3 for Auriol RF Wind Dir
// ---- Define the source of your main Rain Gauge
#define RAIN_OutUnit 3 // 0 for Rain Gauge connected to TX_Unit 0, 1 for TX_Unit 1, 3 for Auriol RF Rain Gauge
// ---- Define the source of your main Solar / UV sensores
#define SRUV_OutUnit 9 // 0 for Solar Rad / UV sensors connected to TX_Unit 0, 1 for TX_Unit1, 9 for not used
// ---- Define installed Solar / UV Sensors
// ---- Define type of Solar Radiation / UV Sensors
#define Solar_Sensor 0 // 0 not used, 1= Solar Cell "Pyranometer", 2= Apogee SP-110 Self-Powered Pyranometer
#define UV_Sensor 0 // 0 not used, 1= UVM-30A, 2= Reserved, 3= Reserved
#define UV_Transmission 70 // UV Transmission percentage of UV sensor cover material
// --------------------------------------------------------------------------------------
// Extra Sensors Settings and Mapping
// --------------------------------------------------------------------------------------
// ---- Define the TX source and sensor number of each of the five extra sensors, insert 9 if not used.
// ---- Source 0 means TX unit0, 1 means TX unit1... (sensor type SHT21 or HTU21D is number 0, sensor type SHT1x or DHT22 is number 1)
// ---- First field is Source = TX unit number, Second field = Sensor number (0 or 1) in the TX unit
// ---- Example:
// ---- ES0 ES1 ES2 ES3 ES4 ES5 ES6
//#define ExtraSensors_Source { {0,1},{1,0},{9,9},{9,9},{9,9},{9,9},{9,9} }
// {0,1} - First extra sensor, is sensor 1 from TX unit0
// {1,0} - Second extra sensor, is sensor 0 from TX unit1
//----- ES1 ES2 ES3 ES4 ES5
#define ExtraSensors_Source { {9,9},{9,9},{9,9},{9,9},{9,9} }
// --------------------------------------------------------------------------------------
// ADVANCED FEATURE - Soil / Leaf Interface Settings
// --------------------------------------------------------------------------------------
#define SoilLeaf_Interface 0 // 0= Not used, 1= In use
// ---- Soil & Leaf Sensors Mapping
// ---- Use the same logic than for Extra Sensors
// ---- As source use the TX Unit number where the Soil / Leaf is connected
// ---- For an unused sensor use 9 in both fields
// S1 S2 S3 S4
#define SoilTempSensors_Source { {9,9},{9,9},{9,9},{9,9} }
#define LeafTempSensors_Source { {9,9},{9,9},{9,9},{9,9} }
#define SoilMoistSensors_Source { {9,9},{9,9},{9,9},{9,9} }
#define LeafWetSensors_Source { {9,9},{9,9},{9,9},{9,9} }
// Define VWC calculation method
// Method 1 applies only for VH400 soil moisture sensor
//
// METHOD 1 - Conversion from voltage to VWC (volumetric water content) is done using the piecewise regressions provided by the manufacturer
// at http://www.vegetronix.com/Products/VH400/VH400-Piecewise-Curve.phtml
//
// METHOD 2 - Used for any sensor which have a linear output between voltage and VWC (0V=0VWC, maxV=100VWC) .
#define VWC_CalcMethod 1 // Use 1 or 2
// Max and Min output voltage of the analog sensors connected to Soil / Leaf Interface
// Default value for Decagon Devices LWS Leaf Wetness Sensor (5V power): Max. Output Voltage - 1400mV (max wetness), Min Output Voltage - 530mV (dry)
// ADC1 ADC2 ADC3 ADC4
const unsigned int AnalogSensor_MaxVoltOut[4] = { 3000, 1400, 5000, 5000 }; // Values in miliVolt
const unsigned int AnalogSensor_MinVoltOut[4] = { 0, 530, 0, 0 };
// --------------------------------------------------------------------------------------
// Enable / Disable Relay Data to Wireless Display Units (Don't enable without an antenna attached to RF output)
// --------------------------------------------------------------------------------------
#define Relay_Data 0 // 0= Disable, 1= Enable
// --------------------------------------------------------------------------------------
// Davis compatible Data Logger Settings
// --------------------------------------------------------------------------------------
#define Logger_Enable 1 // 0= Disable, 1= Enable
byte ARCHIVE_PERIOD = 5; // Default Archive Period in Minutes (Usable values: 1, 5, 10, 15, 30, 60 or 120)
// --------------------------------------------------------------------------------------
// Enable / Disable GPO - General Purpose Output (on boards <= v5.xx use Led+, Led- pins)
// --------------------------------------------------------------------------------------
#define UseGPO 0 // 0=Disable, 1= Enable
// --------------------------------------------------------------------------------------
// Test Mode : Never run a live system in test mode
// --------------------------------------------------------------------------------------
#define TestMode false // false or true
// --------------------------------------------------------------------------------------
// Hardware settings
// --------------------------------------------------------------------------------------
// ---- Define your RX board, main version number
#define Board_Version 6 // 6 for all RX boards v6.xx, 5 for all RX boards v5.xx, 4 for all RX boards v4.xx
// ---- Define LCD I2C address
// Only change this if your LCD don't display any data. I2C_Scanner utility may help you to find the address of your LCD display
// Default address will work most of the times!
#define LCD_I2C_Address 0x27
// --------------------------------------------------------------------------------------
// Presure Sensor Address (no need to change)
// --------------------------------------------------------------------------------------
//#define BMP085_ADDRESS 0x77 // I2C address of BMP085 or BMP180
// --------------------------------------------------------------------------------------
// SHT31 I2C Address - Default address will work most of the times!
// --------------------------------------------------------------------------------------
#define SHT31_address 0x44 // Default value is 0x44, but it can be changed to 0x45
// ---------------------------------------------------------------------------------------------------
// End of user configurable options
// ---------------------------------------------------------------------------------------------------Thanks
Chris