[Barrow4491]

Werk,
I have re compiled and uploaded b013 and the temperature displays as negative (refer attached image).
I have attached my config file
Thanks
Jim

Code:

 -------------------------------------------------------------------------------------- //   User configurable options  // -------------------------------------------------------------------------------------- // -------------------------------------------------------------------------------------- //   Define ID and TX unit number // -------------------------------------------------------------------------------------- #define StationID  0xA1    // Must be equal to your RX Unit (Value from 0x00 to 0xFF)   #define UnitID        0    // If you use only one TX unit define it as UnitID = 0                            // For a second TX unit, define it as UnitID = 1 // -------------------------------------------------------------------------------------- //   Define type of Temperature / Humidity sensor used as Sensor 0 and / or Sensor 1 // -------------------------------------------------------------------------------------- #define TH_Sensor0  1      // [SENSOR 0] - 0 for SHT2x sensor, 1 for SHT31 sensor, 2 for HTU21 sensor, 9 for Not Used #define TH_Sensor1  9      // [SENSOR 1] - 0 for SHT1x sensor, 1 for DHT22 sensor, 9 for Not Used // -------------------------------------------------------------------------------------- //   Define which data this unit will send. 0 = Not send this data, 1= Send this data  // -------------------------------------------------------------------------------------- #define ID0  1   // Temp/Hum Data  #define ID1  0   // Not Used #define ID2  1   // Wind data #define ID3  1   // Rain data #define ID4  1   // UV / SolRad data #define ID5  1   // Hardware Status - System Temp, Battery Voltage etc #define ID7  0   // Send Soil & Leaf Temperature Data #define ID9  0   // Send Soil & Leaf Moisture / Wetness Data // -------------------------------------------------------------------------------------- //   Define which Temp / Hum sensor controls the fan, and threshold values // -------------------------------------------------------------------------------------- #define FanControlSensor  0      // 0 for Sensor 0, 1 for Sensor 1 (which sensor is used to control the RS Fan) #define fanOn_HiTemp     38      // RS Fan turn on when outside temperature is >= than this value (ºC)  #define fanOn_LowTemp     2      // RS Fan turn on when outside temperature is <= than this value (ºC)  #define fanOn_LowWind     1      // RS Fan turn on when Wind Average is <= than this value (m/s) // -------------------------------------------------------------------------------------- //   Define type of Wind Speed sensor. See below for allowed types // -------------------------------------------------------------------------------------- /*  --- Fine Offset Anemometers ---  Use 1O for standard FO anemometers  Use 11 for FO anemometer modified with 1 hall effect sensor  --- Inspeed Anemometers ---  Use 20 for Inspeed Vortex, digital 8 pulse revolution anemometer  Use 21 for Inspeed Vortex, hall efect sensor  Use 22 for Inspeed Vortex, read switch sensor    --- Davis Anemometers ---  Use 30 for Davis 6410, 7911 anemometer    --- Novalynx Anemometers ---  Use 40 for Novalynx, model 200-WS-02F  --- Environmental Measurements Limited ---  Use 50 for EML, model WSD1  --- Didcot Instrument Company ---  Use 60 for DIDCOT, model DWR205 */ #define WSpeedSensor_Type 30             // SEE INFO ABOVE!!! // -------------------------------------------------------------------------------------- //   Define type of Wind Direction sensor // -------------------------------------------------------------------------------------- /*  --- Fine Offset Wind Vane ---  Use 1O for standard FO wind vane    --- Inspeed Wind Vane ---  Use 20 for Inspeed E-Vane 2    --- Davis Wind Vane ---  Use 30 for Davis 6410 wind vane    --- Novalynx Wind Vane  Use 40 for Novalynx, model 200-WS-02F    --- Environmental Measurements Limited Wind Vane ---  Use 50 for EML, model model WSD1      --- Didcot Instrument Company ---  Use 60 for DIDCOT, model DWD205 */ #define WDirSensor_Type  30  // SEE INFO ABOVE!!! // -------------------------------------------------------------------------------------- //          Inspeed Vane Calibration //    Calibration values for Inspeed E-Vane 2 // -------------------------------------------------------------------------------------- #define WDir_min         60 #define WDir_max        990 #define WDir_offs         0 // -------------------------------------------------------------------------------------- //   Define Rain Gauge tip boucket value (mm) // -------------------------------------------------------------------------------------- /*   Use 0.300 for standard FineOfset rain gauges (Datasheet value = 0.2794)   Use 0.200 for standard Davis rain gauges */   #define COLLECTOR_TYPE  0.200  // Please note: Values must be in metric units. Max. resolution: 3 decimal digits     // -------------------------------------------------------------------------------------- //   Soil / Leaf Interface Enable Disable // -------------------------------------------------------------------------------------- #define SoilLeaf_Interface     0   // 0 = Soil Leaf Interface not used, 1 = Enable Soil Leaf Interface #define Number_AnalogSensors   2   // Up to 4 analog sensors // -------------------------------------------------------------------------------------- //   Hardware settings  // -------------------------------------------------------------------------------------- // SHT31 I2c Address // Default address will work most of the times! #define SHT31_address 0x44           // Default value is 0x44, but it can be changed to 0x45  // -------------------------------------------------------------------------------------- //   Debug // -------------------------------------------------------------------------------------- #define Debug_Enable      false #define DebugID0          false #define DebugID2          false #define DebugID3          false #define DebugID4          false #define DebugID5          false #define Easyweather_Test  false #define Debug_SLinterface false // --------------------------------------------------------------------------------------------------- //     End of user configurable options // ---------------------------------------------------------------------------------------------------