[philipgm]

An update:-
sometimes, after many minutes the Pro4 will start receiving data, but it can be many seconds between data packets and only at about 3 or 4% RF Efficiency.
I presume the RX unit is deaf! I have a spare but not sure how easy it is to replace.
Unfortunately the unit won't receive data at all now.
Cheers
Philip.

Another update:-
I think the RX unit is ok. I temporary connected a spare rx board and still no good. I checked the 'Data' connection and there is data there, so not sure whats happening.
I am using Arduino version 1.8.19, and ESP32 v 1.0.6, with the supplied library. (nothing else is in the Library)

I am using latest Firmware RX_v6.2_b005 with settings  Arduino IDE  1.8.19 - ESP32 v2.0.2, but it wont compile like that but it will with ESP32 v1.0.6.

==================
I am just setting up the new Pro4 RX unit using the OOK 433Mhz TX board.
the Pro2 RX board works fine with RF Efficiency of 99.90%.
When the Pro4 RX starts it goes to the page to wait for the T W R to receive data. Nothing happens and after a few minuted the page changes to a pink page which says
"Not Receiving Data"
Below are the Debug Messages. A couple of times I had the unit working  with RF Efficiency of about 2.00%.
Any ideas please.
Ta
Philip
======================
Setting hardware watchdog timer...

Brownout detector was triggered

⸮##⸮!⸮⸮C⸮ͅ⸮ŭ⸮⸮⸮k#״`⸮<⸮kū⸮⸮N7ɝ⸮⸮+̅a)⸮*⸮!⸮⸮⸮i⸮Setting hardware watchdog timer...
Checking for latest software version...
Installed version: v6.2_b005
   Latest version: v6.2_b005
Congratulations. Your system is running latest software.

MDNS responder setup correctly.
WEB Server started on port 80
VP Server started on port 22220
172
0
0
30
30
6
2022
106
0
0
106
0
1
RFM95 goes to Sleep Mode.
433MHz radio init DONE!

And then nothing more!

[uncle_bob]

I don't have experience with that exact unit and until Werk has a say (and I could be completely wrong), but I would be checking the soldering around the receiver module, ensuing its the correct module and following that, swap it out.

Good luck!

[werk_ag]

...
I am just setting up the new Pro4 RX unit using the OOK 433Mhz TX board.
the Pro2 RX board works fine with RF Efficiency of 99.90%.
When the Pro4 RX starts it goes to the page to wait for the T W R to receive data. Nothing happens and after a few minuted the page changes to a pink page which says
"Not Receiving Data"
...

Please upgrade firmware to v6.2_b006
Update the libraries and compile using ESP32 2.0.4

[Petr-meteo]

Hello.
Also the OOK 433Mhz transmission between the the Pro2 Universal TX and the Pro4 RX did not work for me.

Now after upgrading to version 6.2_b006 everything works as it should.

Compiled with Arduino IDE 1.8.19 and ESP32 2.0.4


Thank you for your work on this project Werk_AG

Petr

[werk_ag]

Hi Petr,

Thanks for the feedback and long time support of the WeatherDuino project.

Rgs.
Werk_AG

[werk_ag]

...

Checked my RX unit and working 100%, I reset it lots of times and working every time - Fixed

Great Job working out the problem
Thanks Paul

Thanks for the feedback