Hi Werk_AG,
tnx for coming back. Yes I had upgraded and the latest Version of CumulusMX 5.1.5 running. Today I changed to TCP Feed an pasted the IP Adress of the RX in the StationSettings. But Cumulus kept silent.
So i did a rollback to the last working Version 5.1.0 and tried USB and TCP. --> Again silence und even the same Error Messages as in my InitPost
Next I plugged the RX to Arduino IDE and listened via Serial Monitor with the MainSketch (V.6.3_b008)
Reset Button pressed - >
13:39:44.959 -> ⸮a#⸮!⸮⸮⸮!⸮ !⸮⸮⸮A⸮⸮c#i⸮⸮⸮*⸮i!⸮⸮,⸮i⸮+a{⸮1P⸮⸮⸮!⸮Setting hardware watchdog timer...
13:39:45.419 -> Logger chip status register: 10001100
13:39:45.419 -> Manufacturer ID: FF
13:39:45.419 -> Device ID (part 1): FF
13:39:45.419 ->
13:39:53.377 -> Attempting connection to: OE3MAA
13:39:53.543 -> . . . . . . . . . . . . .
13:39:55.599 -> Connected to: OE3MAA
13:39:55.599 -> WiFi (RSSI): -72 dBm
13:39:55.599 -> IP Address: 192.168.0.xxx
13:39:55.599 -> Gateway IP: 192.168.0.1
13:39:55.599 -> SubnetMask: 255.255.255.0
13:39:55.599 -> MAC address: 30:C6:F7:29:A4:xx
13:39:55.599 -> .
13:39:55.599 -> MDNS responder setup correctly.
13:39:56.627 -> WEB Server started on port 80
13:39:57.026 -> 172
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.125 -> RFM95 init done.
13:39:58.319 -> Wunderground IP: 44.207.123.184
13:39:58.319 -> WeatherCloud IP: 94.127.186.149
13:40:01.238 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 3 Full Message: A10103,C8,0,D,0
13:40:06.742 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,BFA,E09,E44,B07
13:40:23.749 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,BFD,E05,E46,B22
13:40:40.754 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,C07,DFB,E49,B1C
13:40:43.043 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 5 Full Message: A10105,52E,32F,1,177
13:40:57.760 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,C06,DF3,E4E,AF0
13:41:03.639 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 3 Full Message: A10103,C8,0,D,0
13:41:07.460 -> Station ID: A1 Dev. Type: AQM-III Unit ID: 0 TX Mode: LoRa Sensor ID: 12 Full Message: A10B0C,1E001E,82517EA,63701A9,FFFFFFFF
Next i uploaded the "4proDB_flash_write_test" and monitored the Output via Serial Monitor:
13:19:44.678 -> ⸮k
13:19:44.678 -> Z@⸮)⸮!!⸮I_J0i+#)V⸮ĉ⸮⸮⸮!+B#a⸮⸮1ZH!!ARFM95 init done.
13:19:44.909 -> RFM95 goes to Sleep Mode.
13:19:44.976 -> Point 1
13:19:44.976 -> Logger chip status register: 10001100
13:19:44.976 -> Manufacturer ID: C0
13:19:44.976 -> Device ID (part 1): 2A
13:19:44.976 ->
13:19:44.976 -> Point 2
Here the output stops after Point 2... What´s interesting: There are differences in the Output of Manufacturer ID and Device ID under Test- and Mainversion Sketch.
Would appreciate any advice for further testing. Thank you.
Best, PapaErde
tnx for coming back. Yes I had upgraded and the latest Version of CumulusMX 5.1.5 running. Today I changed to TCP Feed an pasted the IP Adress of the RX in the StationSettings. But Cumulus kept silent.
So i did a rollback to the last working Version 5.1.0 and tried USB and TCP. --> Again silence und even the same Error Messages as in my InitPost
Next I plugged the RX to Arduino IDE and listened via Serial Monitor with the MainSketch (V.6.3_b008)
Reset Button pressed - >
13:39:44.959 -> ⸮a#⸮!⸮⸮⸮!⸮ !⸮⸮⸮A⸮⸮c#i⸮⸮⸮*⸮i!⸮⸮,⸮i⸮+a{⸮1P⸮⸮⸮!⸮Setting hardware watchdog timer...
13:39:45.419 -> Logger chip status register: 10001100
13:39:45.419 -> Manufacturer ID: FF
13:39:45.419 -> Device ID (part 1): FF
13:39:45.419 ->
13:39:53.377 -> Attempting connection to: OE3MAA
13:39:53.543 -> . . . . . . . . . . . . .
13:39:55.599 -> Connected to: OE3MAA
13:39:55.599 -> WiFi (RSSI): -72 dBm
13:39:55.599 -> IP Address: 192.168.0.xxx
13:39:55.599 -> Gateway IP: 192.168.0.1
13:39:55.599 -> SubnetMask: 255.255.255.0
13:39:55.599 -> MAC address: 30:C6:F7:29:A4:xx
13:39:55.599 -> .
13:39:55.599 -> MDNS responder setup correctly.
13:39:56.627 -> WEB Server started on port 80
13:39:57.026 -> 172
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.026 -> 0
13:39:57.125 -> RFM95 init done.
13:39:58.319 -> Wunderground IP: 44.207.123.184
13:39:58.319 -> WeatherCloud IP: 94.127.186.149
13:40:01.238 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 3 Full Message: A10103,C8,0,D,0
13:40:06.742 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,BFA,E09,E44,B07
13:40:23.749 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,BFD,E05,E46,B22
13:40:40.754 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,C07,DFB,E49,B1C
13:40:43.043 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 5 Full Message: A10105,52E,32F,1,177
13:40:57.760 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 0 Full Message: A10100,C06,DF3,E4E,AF0
13:41:03.639 -> Station ID: A1 Dev. Type: TX_LoRa Unit ID: 0 TX Mode: LoRa Sensor ID: 3 Full Message: A10103,C8,0,D,0
13:41:07.460 -> Station ID: A1 Dev. Type: AQM-III Unit ID: 0 TX Mode: LoRa Sensor ID: 12 Full Message: A10B0C,1E001E,82517EA,63701A9,FFFFFFFF
Next i uploaded the "4proDB_flash_write_test" and monitored the Output via Serial Monitor:
13:19:44.678 -> ⸮k
13:19:44.678 -> Z@⸮)⸮!!⸮I_J0i+#)V⸮ĉ⸮⸮⸮!+B#a⸮⸮1ZH!!ARFM95 init done.
13:19:44.909 -> RFM95 goes to Sleep Mode.
13:19:44.976 -> Point 1
13:19:44.976 -> Logger chip status register: 10001100
13:19:44.976 -> Manufacturer ID: C0
13:19:44.976 -> Device ID (part 1): 2A
13:19:44.976 ->
13:19:44.976 -> Point 2
Here the output stops after Point 2... What´s interesting: There are differences in the Output of Manufacturer ID and Device ID under Test- and Mainversion Sketch.
Would appreciate any advice for further testing. Thank you.
Best, PapaErde