An update:-
sometimes, after many minutes the Pro4 will start receiving data, but it can be many seconds between data packets and only at about 3 or 4% RF Efficiency.
I presume the RX unit is deaf! I have a spare but not sure how easy it is to replace.
Unfortunately the unit won't receive data at all now.
Cheers
Philip.
Another update:-
I think the RX unit is ok. I temporary connected a spare rx board and still no good. I checked the 'Data' connection and there is data there, so not sure whats happening.
I am using Arduino version 1.8.19, and ESP32 v 1.0.6, with the supplied library. (nothing else is in the Library)
I am using latest Firmware RX_v6.2_b005 with settings Arduino IDE 1.8.19 - ESP32 v2.0.2, but it wont compile like that but it will with ESP32 v1.0.6.
==================
I am just setting up the new Pro4 RX unit using the OOK 433Mhz TX board.
the Pro2 RX board works fine with RF Efficiency of 99.90%.
When the Pro4 RX starts it goes to the page to wait for the T W R to receive data. Nothing happens and after a few minuted the page changes to a pink page which says
"Not Receiving Data"
Below are the Debug Messages. A couple of times I had the unit working with RF Efficiency of about 2.00%.
Any ideas please.
Ta
Philip
======================
Setting hardware watchdog timer...
Brownout detector was triggered
⸮##⸮!⸮⸮C⸮ͅ⸮ŭ⸮⸮⸮k#״`⸮<⸮kū⸮⸮N7ɝ⸮⸮+̅a)⸮*⸮!⸮⸮⸮i⸮Setting hardware watchdog timer...
Checking for latest software version...
Installed version: v6.2_b005
Latest version: v6.2_b005
Congratulations. Your system is running latest software.
MDNS responder setup correctly.
WEB Server started on port 80
VP Server started on port 22220
172
0
0
30
30
6
2022
106
0
0
106
0
1
RFM95 goes to Sleep Mode.
433MHz radio init DONE!
And then nothing more!
sometimes, after many minutes the Pro4 will start receiving data, but it can be many seconds between data packets and only at about 3 or 4% RF Efficiency.
I presume the RX unit is deaf! I have a spare but not sure how easy it is to replace.
Unfortunately the unit won't receive data at all now.
Cheers
Philip.
Another update:-
I think the RX unit is ok. I temporary connected a spare rx board and still no good. I checked the 'Data' connection and there is data there, so not sure whats happening.
I am using Arduino version 1.8.19, and ESP32 v 1.0.6, with the supplied library. (nothing else is in the Library)
I am using latest Firmware RX_v6.2_b005 with settings Arduino IDE 1.8.19 - ESP32 v2.0.2, but it wont compile like that but it will with ESP32 v1.0.6.
==================
I am just setting up the new Pro4 RX unit using the OOK 433Mhz TX board.
the Pro2 RX board works fine with RF Efficiency of 99.90%.
When the Pro4 RX starts it goes to the page to wait for the T W R to receive data. Nothing happens and after a few minuted the page changes to a pink page which says
"Not Receiving Data"
Below are the Debug Messages. A couple of times I had the unit working with RF Efficiency of about 2.00%.
Any ideas please.
Ta
Philip
======================
Setting hardware watchdog timer...
Brownout detector was triggered
⸮##⸮!⸮⸮C⸮ͅ⸮ŭ⸮⸮⸮k#״`⸮<⸮kū⸮⸮N7ɝ⸮⸮+̅a)⸮*⸮!⸮⸮⸮i⸮Setting hardware watchdog timer...
Checking for latest software version...
Installed version: v6.2_b005
Latest version: v6.2_b005
Congratulations. Your system is running latest software.
MDNS responder setup correctly.
WEB Server started on port 80
VP Server started on port 22220
172
0
0
30
30
6
2022
106
0
0
106
0
1
RFM95 goes to Sleep Mode.
433MHz radio init DONE!
And then nothing more!