[bombenm]

When i remove the touch cable,  there are no effects.  Screen shows the menu page.
Yes, I am using the supplied libraries.

There is something strange here... I can't see how it can jump to the Menu screen even with the touch cables removed.
Out of curiosity, can you post your Config_Options.h file?

Code:

 
// --------------------------------------------------------------------------------------
//  WeatherDuino Pro2 PLUS Receiver - Version: P2AT2560_RX_v8.3_b002
//                 Start of user configurable options 
// --------------------------------------------------------------------------------------
// If you need help about any of the user configurable settings, please first do a search
// at the WeatherDuino Pro2 support forum. If you don't find any relevant info, then post
// a new thread.
//
// --------------------------------------------------------------------------------------
//   Define Name and URL for this weather station
//   This data is used list you in the WeatherDuino Online Weather Station Map
// --------------------------------------------------------------------------------------
const char* WeatherStation_Name = "WS_Palazzetto_Pordenone";    // DON'T LEAVE EMPTY - Put here your Weather Station name or Location name
const char* WeatherStation_URL  = "https://www.wunderground.com/dashboard/pws/IFRIULIV68";    // If you have an URL to your Meteo Website put it here (can be the WU URL). URL should start with http or https


// --------------------------------------------------------------------------------------
//   Define ID's for this weather station
// --------------------------------------------------------------------------------------
#define Station_ID  0xA1     // Station_ID, use the same value in all TX units
#define Relay_ID    0xA3     // Relay_ID,   use the same value in all WD units


// --------------------------------------------------------------------------------------
//   Define your Weather Station location. Use decimal format for Latitude and Longitude
// --------------------------------------------------------------------------------------
#define LATITUDE      45.97165    // Put here your Station latitude in degrees North (with up to 5 decimal places, don't use less than 3 decimal places)
#define LONGITUDE     12.65838    // Put here your Station longitude in degrees - minus for West (with up to 5 decimal places, don't use less than 3 decimal places)
#define ELEVATION     48         // Put here your Station height above sea level in Meters (no decimal places)


// --------------------------------------------------------------------------------------
//   Define rules for Auto Summer Time Display, and clock adjustment
// --------------------------------------------------------------------------------------
// Example for Australia Eastern Time Zone (Sydney, Melbourne) 
// TimeChangeRule aEDT = {"AEDT", First, Sun, Oct, 2, 660};    //UTC + 11 hours 
// TimeChangeRule aEST = {"AEST", First, Sun, Apr, 3, 600};    //UTC + 10 hours 
// Timezone myTZ(aEDT, aEST); 

TimeChangeRule PST = {"PST", Last, Sun, Mar, 1, 120};   //Portuguese Summer Time -  "UTC + 1" or GMT + 1 or GMT + 2 Italy
TimeChangeRule GMT = {"GMT", Last, Sun, Oct, 2, 60};    //Portuguese Winter Time -  "UTC + 0" or GMT     or GMT + 1 Italy
Timezone myTZ(PST, GMT);


// --------------------------------------------------------------------------------------
//   Define Interface Language
// --------------------------------------------------------------------------------------     
#include "_lang/it_IT.h"      // Change the language code according to your preference. Keep "_lang/" and the ".h" at the end
                              // Currently available languages: en_GB, fr_FR, de_DE, pt_PT, es_ES, cs_CZ, nl_NL, it_IT, pl_PL

// --------------------------------------------------------------------------------------
//   Define Roll Over Hour for Meteorological Day
// --------------------------------------------------------------------------------------
const byte MeteoDay_HStart = 0;    // Use values from 0 to 23


// --------------------------------------------------------------------------------------
//   Define TFT Display Backlight TimeOut
// --------------------------------------------------------------------------------------
#define SCREENSAVER_TIMEOUT  30    // Timeout for display backlight in minutes (1 to 255). 0 = Always ON 
#define USE_BIGCLOCK          1    // Instead of turn off TFT backlight, show a big clock screen. 0= No, 1= Yes


// --------------------------------------------------------------------------------------
//   Blink the colon on the TFT Top Clock (a precious waste of time, but some may like it!) 
//   This setting only has effect when the system is running in normal mode.
// --------------------------------------------------------------------------------------
#define BLINKCOLON      0    // 0= No, 1= Yes


// --------------------------------------------------------------------------------------
//   Define data display units
// --------------------------------------------------------------------------------------
#define DATE_TIME_FORMAT  0    // 0 for dd-mm-yyyy, 1 for yyyy/mm/dd
#define TEMP_DISPLAY_UNIT 0    // 0 for ºC, 1 for ºF
#define ATM_DISPLAY_UNIT  0    // 0 for mBar, 1 for inHg
#define RAIN_DISPLAY_UNIT 0    // 0 for mm, 1 for inches
#define WIND_DISPLAY_UNIT 0    // 0 for Km/h, 1 for mph, 2 for m/s, 3 for Knots


// --------------------------------------------------------------------------------------
//   Define the type of your Barometric Pressure Sensor
// --------------------------------------------------------------------------------------
#define BAROMETRIC_SENSOR  0   // 0= BME280, 1= BMP280 2= BMP085 / BMP180


// --------------------------------------------------------------------------------------
//   Define the type of your inside Temperature / Humidity Sensor
// --------------------------------------------------------------------------------------
#define INSIDE_TH_SENSOR   0   // 0= BME280, 1= HTU21D, 2= SHT21, 3= SHT31


// --------------------------------------------------------------------------------------
//   Fine adjusts for Inside Temperature and Barometer
// --------------------------------------------------------------------------------------
const int   TemperaturaInt_offset =   -15;   // Inside Temperature Fine Adjust in Tenths of Degree (-4 = -0,4ºC) 
const float pressure_offset       =   -5;   // Pressure Fine Adjust in mB


// --------------------------------------------------------------------------------------
//   Define Wind Speed and Wind Gust resolution - Read carefully
// --------------------------------------------------------------------------------------
#define VP2_WIND_RESOLUTION     0    // If set to 2, set Cumulus Wind Speed and Wind Gust multipliers to 0.448. Wind Resolution 0.72 Km/h
                                     // If set to 1, set Cumulus Wind Speed and Wind Gust multipliers to 0.224. Wind Resolution 0.36 Km/h
                                     // WARNING !!!
                                     // Setting this variable to 2 or 1 allows a better wind speed and gust resolution,
                                     // but also limits the maximum readings to 183.6 Km/h and 91.8 Km/h, respectively.
                                     // If set to 0, system uses Standard Davis wind resolution (1 mph or 0.1mph with LOOP2).
                                     // Weather Display users should set this option to 0 - Standard Davis wind resolution   

// --------------------------------------------------------------------------------------
//   Define use of Wind Gust Spike prevention routines (mostly for FO anemometers)
// --------------------------------------------------------------------------------------
#define WIND_SPIKECONTROL 1   // 0= Disable, 1= Enable


// --------------------------------------------------------------------------------------
//   Define the source of your main outside sensors
// --------------------------------------------------------------------------------------
// ---- If you are using just one TX board, the source for all items should be equal to your single TX Unit ID (most likely zero).
// ---- Define the source of your main Temperature / Humidity sensor
#define TH_SOURCE       0   // 0= Temp/Hum sensor connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Temp / Hum
// ---- Define the source of your Main Wind sensor
#define WIND_SOURCE     0   // 0= Wind instruments connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Wind Speed & Dir
// ---- Define the source of your main Rain Gauge
#define RAIN_SOURCE     0   // 0= Rain Gauge connected to TX_Unit 0, 1= for TX_Unit 1, ..., 3 for Auriol RF Rain Gauge
// ---- Define the source of your main Solar Radiation sensor
#define SOLAR_SOURCE    0   // 0= Solar Radiation sensor connected to TX_Unit 0, 1= for TX_Unit1, ..., 9 for not used
// ---- Define the source of your main UV sensor
#define UV_SOURCE       0  // 0= UV sensor connected to TX_Unit 0, 1= for TX_Unit1, ..., 9 for not used


// --------------------------------------------------------------------------------------
//   Each TX unit can send data from two Temp / Hum sensors. 
//   Here you must define which one will be used as your main outside Temperature / Humidity Sensor
//   SENSOR_0 can be any of the supported I2C T/H sensors (SHT31, SHT21 or HTU21D), SENSOR_1 can be an SHT1x or DHT22
// --------------------------------------------------------------------------------------
#define MAINOUT_TH_SENSOR 1   // 0 for SENSOR_0, 1 for SENSOR_1 


// --------------------------------------------------------------------------------------
//   Define the type of your Solar Radiation sensor
// --------------------------------------------------------------------------------------
//                       1= Solar Cell "Pyranometer"
//                       2= Apogee SP-110 Pyranometer
//                       3= Reserved
//                       4= Apogee SQ-110: Photosynthetically Active Radiation Sensor (Support for this sensor is experimental)

#define SOLAR_SENSOR     1   


// --------------------------------------------------------------------------------------
//   Define the type of your UV sensor
// --------------------------------------------------------------------------------------
//                       1= UVM-30A
//                       2= VEML6075
//                       3= Reserved 
//                      20= Rika RK200-04 (MODBUS)

#define UV_SENSOR        1
const byte UV_Transmission = 65;    // UV Transmission percentage of UV sensor cover material. 


//---------------------------------------------------------
//    Enable / Disable getting Temperature / Humidity from WiFI sensors (Usually the local T/H sensor on Wireless Display units)
//---------------------------------------------------------
#define ENABLE_TH_FROM_WIFISENSORS     0                         // 1= Enable, 0= Disable
#define WIFISENSORS_WEBSERVER_PORT    80                         // Should be the same port defined as WebServer port on the WiFi Wireless Display units. 

                                                    // Example: "192.168.1.152"
const char* WIFIunit_address [][4]= { ""            // IP address of first WiFi sensor
                                    , ""            // IP address of second WiFi sensor
                                    , ""            // IP address of third WiFi sensor
                                    , ""            // IP address of fourth WiFi sensor                           
                                    };


// --------------------------------------------------------------------------------------
//   Extra Sensors Mapping
// --------------------------------------------------------------------------------------
// ---- Define the source and sensor type (number) for each of the seven extra sensors, insert 9 if not used.
//      Sensors SHT31, SHT21 or HTU21D are type 0, sensors SHT1x or DHT22 are type 1
// 
// ---- Source 0 means TX unit0, 1 means TX unit1... 
// ---- Source 5 is for Temperature/Humidity from the Wireless Display units
// ---- Source 6 (Reserved)
// ---- Source 7 is for BIOS Sensor (Only Temperature is shown)
// ---- Source 8 is for Temperature/Humidity from the Air Quality Monitor
//
// ---- First field = Sensor source, Second field = Sensor type (0 or 1 for TX units) 
// ---- Example:
// ----                          ES0   ES1   ES2   ES3   ES4   ES5   ES6     
//#define EXTRASENSORS_SOURCE { {0,1},{1,1},{5,1},{5,0},{9,9},{9,9},{8,0} }
//               {0,1} - First extra sensor (ES0), will be sensor 1 from TX unit0
//               {1,1} - Second extra sensor (ES1), will be sensor 1 from TX unit1
//               {5,1} - Third extra sensor (ES2), will be T/H data from WiFi Sensor 1 (Wireless Display 1)
//               {5,0} - Fourth extra sensor (ES3), will be T/H data from WiFi Sensor 0 (Wireless Display 0)
//               {9,9} - Fifth extra sensor (ES4), not use - not mapped
//               {9,9} - Sixth extra sensor (ES5), not use - not mapped
//               {8,0} - Seventh extra sensor (ES6), will be Temperature / Humidity from the Air Quality Monitor 
//
//-----                        ES0   ES1   ES2   ES3   ES4   ES5   ES6     
#define EXTRASENSORS_SOURCE  { {9,9},{9,9},{9,9},{9,9},{9,9},{9,9},{8,0} }


// --------------------------------------------------------------------------------------
//   Define personalized names for each Extra sensor. Attention, 8 chars maximum
// --------------------------------------------------------------------------------------
//                   Max. Size  [--------] 
const char ESname_1[] PROGMEM = "";            // 8 chars max
const char ESname_2[] PROGMEM = "";            // 8 chars max 
const char ESname_3[] PROGMEM = "";            // 8 chars max
const char ESname_4[] PROGMEM = "";            // 8 chars max
const char ESname_5[] PROGMEM = "";            // 8 chars max
const char ESname_6[] PROGMEM = "";            // 8 chars max
const char ESname_7[] PROGMEM = "Dust TH";     // 8 chars max


// --------------------------------------------------------------------------------------
//   BIOS soil moisture sensor settings
// --------------------------------------------------------------------------------------
// ---- Please use the included BIOS_ID_Scanner sketch to find you BIOS Device ID
#define BIOS_SENSOR_ID   0   // Device ID in HEX format, or 0 not used

// --------------------------------------------------------------------------------------
//   Soil / Leaf Interface Settings and Sensors Mapping
//   (The mapping logic is the same than used with the Extra Sensors)
// --------------------------------------------------------------------------------------
// 0 = Soil Leaf Interface not used
// 1 = Soil Leaf Interface connected to a TX unit
#define SOIL_LEAF_INTERFACE  0   // 0, 1, 

// ---- For Soil & Leaf data from SoilLeaf_Interface wired to a TX unit, use TX Unit number as source 
// ---- For BIOS Soil Temp / Moisture use 7 as source
// ---- To disable use 9 in both fields
//                                 S1    S2    S3    S4
#define SOILTEMPSENSORS_SOURCE  { {9,9},{9,9},{9,9},{9,9} }
#define LEAFTEMPSENSORS_SOURCE  { {9,9},{9,9},{9,9},{9,9} }
#define SOILMOISTSENSORS_SOURCE { {9,9},{9,9},{9,9},{9,9} }
#define LEAFWETSENSORS_SOURCE   { {9,9},{9,9},{9,9},{9,9} }


// --------------------------------------------------------------------------------------
//   Define personalized names for each Soil and Leaf sensor. Attention, 8 chars maximum
// --------------------------------------------------------------------------------------
//              Soil Max. Size  [--------] 
const char SSname_1[] PROGMEM = "1";        // 8 chars max
const char SSname_2[] PROGMEM = "2";        // 8 chars max 
const char SSname_3[] PROGMEM = "3";        // 8 chars max
const char SSname_4[] PROGMEM = "4";        // 8 chars max

//              Leaf Max. Size  [--------] 
const char LSname_1[] PROGMEM = "1";        // 8 chars max
const char LSname_2[] PROGMEM = "2";        // 8 chars max
const char LSname_3[] PROGMEM = "3";        // 8 chars max
const char LSname_4[] PROGMEM = "4";        // 8 chars max


// --------------------------------------------------------------------------------------
//   Define VWC calculation method
// --------------------------------------------------------------------------------------
//
// Method 1 applies only for VH400 soil moisture sensor
//
// METHOD 1 - Conversion from voltage to VWC (volumetric water content) is done using the piecewise regressions provided by the manufacturer 
// at http://www.vegetronix.com/Products/VH400/VH400-Piecewise-Curve.phtml 
//
// METHOD 2 - Used for any sensor which have a linear output between voltage and VWC (0V=0VWC, maxV=100VWC) .

#define VWC_CALCMETHOD   1  // 1 or 2


// --------------------------------------------------------------------------------------
//   Define Max and Min output voltage of the analog sensors connected to Soil / Leaf Interface
// --------------------------------------------------------------------------------------
//
// Default value for Decagon Devices LWS Leaf Wetness Sensor (3.3V power): Max. Output Voltage - 1395mV (max wetness), Min Output Voltage - 530mV (dry)

//                                              ADC1  ADC2  ADC3  ADC4  
const uint16_t AnalogSensor_MaxVoltOut[4]   = { 3000, 1395, 5000, 5000 };    // Values in miliVolts
const uint16_t AnalogSensor_MinVoltOut[4]   = {    0,  530,    0,    0 };


// --------------------------------------------------------------------------------------
//   Broadcasting Data to Wireless Display Units
// --------------------------------------------------------------------------------------
#define BROADCAST_DATA       1          // 0= Disables Data Broadcast, 1= Broadcast by WiFi, 2= Broadcast by RF
#define UDP_BROADCAST_PORT   9889       // UDP broadcast port - must be the same defined on WiFi Wireless Display units.


// --------------------------------------------------------------------------------------
//   Davis compatible Data Logger Settings
// --------------------------------------------------------------------------------------
#define LOGGER_ENABLE    1   // 0= Disable 1= Enable
byte ARCHIVE_PERIOD  =   5;  // Default Archive Period in Minutes (Usable values: 1, 5, 10, 15, 30)


// --------------------------------------------------------------------------------------
//   Define type of your Weather Software 
// --------------------------------------------------------------------------------------
#define WEATHERSOFT      0   // 0= CumulusMX, 1= Any other (Cumulus 1, WeewX, Weather Display, etc.)


// --------------------------------------------------------------------------------------
//   Easyweather Mode output 
// --------------------------------------------------------------------------------------
#define EASYWEATHER_OUT  0   // 0= Disable (defaut) 1= Enable


// --------------------------------------------------------------------------------------
//   Enable / Disable WiFi connection
// --------------------------------------------------------------------------------------
#define ENABLE_INTERNET     1                        // 1= Enable Internet connection, 0= Disable


// --------------------------------------------------------------------------------------
//   Enable / Disable time sync with an NTP server
// --------------------------------------------------------------------------------------
#define ENABLE_NTP          1                        // 1= Enable Sync time with NTP servers, 0= Disable


// --------------------------------------------------------------------------------------
//   NTP Servers - Enable only one
// --------------------------------------------------------------------------------------  
#define TIMESERVER "pool.ntp.org"
//#define TIMESERVER "time.nist.gov"                 // ntp1.nl.net NTP server
//#define TIMESERVER "80.96.196.58"                  // timp.mcsi.ro
//#define TIMESERVER "193.79.237.14"                 // ntp1.nl.net NTP server


// --------------------------------------------------------------------------------------
//   Enable / Disable data transmission to Weather Wunderground
// --------------------------------------------------------------------------------------
#define ENABLE_WU_UPLOAD   0                         // 1= Enable upload to Wunderground, 0= Disable
#define WU_UPLOAD_INTEMP   0                         // 1= Enable upload of Inside Temperature / Humidity, 0= Disable
byte    WU_upload_period = 5;                        // Period in minutes between uploads to WU (Should be >= 3 minutes, if less defaults to 3 minutes) 


// --------------------------------------------------------------------------------------
//   Enable / Disable data transmission to ThingSpeak
// --------------------------------------------------------------------------------------
#define ENABLE_TS_UPLOAD          1                  // 1= Enable, 0= Disable


// --------------------------------------------------------------------------------------
//   Air Quality Monitor - Upload and insert data in a SQL table at your own server ----
//   Be sure you have already created the database and table. See AirQuality_LogToSQL.php script for info
// --------------------------------------------------------------------------------------
#define ENABLE_AQM_TO_MYSERVER    1                  // 1= Enable, 0= Disable


// --------------------------------------------------------------------------------------
//   Enable / Disable internal Web Server 
// --------------------------------------------------------------------------------------
#define ENABLE_WEBSERVER          1                  // 1= Enable 0= Disable
#define WEBSERVER_PORT           80                  // WebServer port (default 80) 


// --------------------------------------------------------------------------------------
//   Enable / Disable GPIO routines - General Purpose Input / Output ports
// --------------------------------------------------------------------------------------
#define USE_GPIO  1   // 0=Disable, 1= Enable


// --------------------------------------------------------------------------------------
//   Define display order of data screens on the TFT
//   Use sequentially numbers from 1 to 4.
// --------------------------------------------------------------------------------------
#define AirQuality_Data    1
#define TXinfo_Data        2
#define ExtraSensors_Data  3
#define SoilLeaf_Data      4


// --------------------------------------------------------------------------------------
//   Test Mode : Never run a live system in test mode 
// --------------------------------------------------------------------------------------
bool Test_Mode = false;    // false= Normal working mode, true= Test mode only (no logger, no usb connection)


// --------------------------------------------------------------------------------------
//   Erase the Data Logger Flash Memory on Factory Reset  
// --------------------------------------------------------------------------------------
#define ERASE_DATALOGGER   0    // 0= NO (default), 1= YES


// --------------------------------------------------------------------------------------
//   Transmitter Software Version 
// --------------------------------------------------------------------------------------
#define TX_SOFTWARE_VERSION  7    // Use main version number only (This setting affects VBat readings)
                                  // Hint: TX software versions released prior to Dec 2018 are all < 7 


// *************************************************************************************
//     Hardware Settings 
// *************************************************************************************

// --------------------------------------------------------------------------------------
//   Define PCB Version Number
// --------------------------------------------------------------------------------------
//                              Take particular attention to this setting.
//                              Your system may not work properly if you define a wrong pcb version number.
//                              In case of doubt check what is printed in your pcb.

#define PCB_VERSION   20     // PCB version number, without the decimal point Ex: PCB v1.3 = 13 (integer number)


// --------------------------------------------------------------------------------------
//   Define your Display type
// --------------------------------------------------------------------------------------
#define DISPLAY_TYPE     3    // 1= LCD 20x4, 3= TFT 320x240 ILI9341


// --------------------------------------------------------------------------------------
//   Define Type of your Touch Panel (Applies only to PCB Versions >= 20)
// --------------------------------------------------------------------------------------
#define TOUCH_TYPE       3    // 3= Default Setting, 1= Setting for displays with the "Yellow Pins"


// --------------------------------------------------------------------------------------
//   Define LCD I2C address 
// --------------------------------------------------------------------------------------
// Only change this if your LCD don't display any data. I2C_Scanner utility may help you to find the address of your LCD display
// Default address will work most of the times!
#define LCD_ADDRESS      0x27   


// --------------------------------------------------------------------------------------
//   SHT31 I2C Address - Default address will work most of the times!
// --------------------------------------------------------------------------------------
#define SHT31_ADDRESS       0x44       // Default value is 0x44 which works with the majority of SHT31 modules, however some unusual modules use 0x45. Change if needed.


// --------------------------------------------------------------------------------------
//   Presure Sensor Address (no need to change)
// --------------------------------------------------------------------------------------
//#define BMP085_ADDRESS    0x77       // I2C address of BMP085 or BMP180


// --------------------------------------------------------------------------------------
//   Debug helper - Print debug messages to serial monitor. For testing purposes ONLY.
//
//   !!! NEVER LEAVE ANY OF THESE DEBUG FUNCTIONS ACTIVE WHEN THE STATION IS CONNECTED BY USB TO ANY WEATHER SOFTWARE !!! 
// --------------------------------------------------------------------------------------
//#define PRINT_DEBUG_WIFI
//#define PRINT_DEBUG_NTP_UPDATE      // Prints to serial monitor messages related to sync time with NTP server
//#define PRINT_DEBUG_WU_UPLOAD       // Prints to serial monitor messages related to Weather Underground upload.
//#define PRINT_DEBUG_TS_UPLOAD
//#define PRINT_DEBUG_MYSERVER_UPLOAD
//#define PRINT_DEBUG_VCHECK
//#define PRINT_DEBUG_TCP_SERVER
//#define PRINT_DEBUG_AURIOL
//#define PRINT_DEBUG_BIOS
//#define PRINT_DEBUG_RF_MESSAGES
//#define PRINT_DEBUG_WIFI_SENSORS
//#define PRINT_GENERALDEBUG

// ---------------------------------------------------------------------------------------------------
//     End of user configurable options
// ---------------------------------------------------------------------------------------------------