[Barrow4491]

Werk,

I get the following error, vI assume regarding a missing library file???
I have attached my Config file for your perusal
Thanks
Jim

Arduino: 1.7.11 (Windows 8.1), Board: "Arduino Mega or Mega 2560, ATmega2560 (Mega 2560)"

WeatherDuinoPro2Plus_RX_v100_b015_09122016.ino:24:22: fatal error: Timezone.h: No such file or directory

compilation terminated.

Error compiling.

  This report would have more information with
  "Show verbose output during compilation"
  enabled in File > Preferences.

Code:

// --------------------------------------------------------------------------------------
//     Start of user configurable options 
// --------------------------------------------------------------------------------------


// --------------------------------------------------------------------------------------
//   Define ID's for this weather station
// --------------------------------------------------------------------------------------
#define Station_ID   0xA1    // Station_ID, use the same value in all TX units
#define Relay_ID     0xB3    // Relay_ID,   use the same value in all WD units


// --------------------------------------------------------------------------------------
//   Define your Weather Station location
// --------------------------------------------------------------------------------------
#define LATITUDE      -19    // Put here your Station latitude in tenths of degrees North
#define LONGITUDE     146    // Put here your Station longitude in tenths of degrees (minus for West)
#define ELEVATION      55    // Put here your Station height above sea level in Meters


// --------------------------------------------------------------------------------------
//   Define rules for Auto Summer Time Display, and clock adjustment
// --------------------------------------------------------------------------------------
// Example for Australia Eastern Time Zone (Sydney, Melbourne) 
// TimeChangeRule aEDT = {"AEDT", First, Sun, Oct, 2, 660};    //UTC + 11 hours 
// TimeChangeRule aEST = {"AEST", First, Sun, Apr, 3, 600};    //UTC + 10 hours 
// Timezone myTZ(aEDT, aEST); 

TimeChangeRule aEDT = {"AEST", First, Sun, Oct, 2, 600};   //UTC + 10 hours 
Timezone myTZ(aEDT, aEST);


// --------------------------------------------------------------------------------------
//   Define Roll Over Hour for Meteorological Day
// --------------------------------------------------------------------------------------
#define MeteoDay_HStart 9    // Use values from 0 to 23


// --------------------------------------------------------------------------------------
//   Define your Display type
// --------------------------------------------------------------------------------------
#define DisplayType       3   // 1= LCD 20x4, 3= TFT 320x240 ILI9341

// --------------------------------------------------------------------------------------
//   Define Display Backlight TimeOut
// --------------------------------------------------------------------------------------
const byte  BackLight_Timeout = 0;   // Timeout for display backlight in minutes (1 to 255). 0 = Always ON 
#define Use_ScreenSaver           1    // Instead of turn off backlight show a big clock screen. 0= No, 1= Yes

// --------------------------------------------------------------------------------------
//   Define data display units
// --------------------------------------------------------------------------------------
#define Date_Time_Format 0     // 0 for dd-mm-yyyy, 1 for yyyy/mm/dd
byte Temp_Display_Unit = 0;    // 0 for ºC, 1 for ºF
byte ATM_Display_Unit  = 0;    // 0 for mBar, 1 for inHg
byte Rain_Display_Unit = 0;    // no setting, always mm
byte Wind_Display_Unit = 3;    // 0 for Km/h, 1 for mph, 2 for m/s, 3 for Knots


// --------------------------------------------------------------------------------------
//   Define the type of your Barometric Pressure Sensor
// --------------------------------------------------------------------------------------
#define Barometric_Sensor  1   // 0= BME280, 1= BMP280 2= BMP085 / BMP180


// --------------------------------------------------------------------------------------
//   Define the type of your inside Temperature / Humidity Sensor
// --------------------------------------------------------------------------------------
#define InsideTH_Sensor  0   // 0= BME280, 1= HTU21D, 2= SHT21, 3= SHT31


// --------------------------------------------------------------------------------------
//   Fine adjusts for Inside Temperature and Barometer
// --------------------------------------------------------------------------------------
const int   TemperaturaInt_offset =   0;   // Inside Temperature Fine Adjust in Tenths of Degree (-4 = -0,4ºC) 
const float pressure_offset       =   0;   // Pressure Fine Adjust in mB


// --------------------------------------------------------------------------------------
//   Define the type of your outside Temperature / Humidity Sensor
// --------------------------------------------------------------------------------------
#define MainOutTH_Sensor 0   // 0 for sensor type SHT31, SHT21 or HTU21D, 1 for sensor type SHT1x or DHT22 


// --------------------------------------------------------------------------------------
//   Define Wind Speed and Wind Gust resolution
// --------------------------------------------------------------------------------------
// This setting only have effect when the software is used in Davis VP emulation mode
#define VP2_WindRes     0    // If set to 2, set Cumulus Wind Speed and Wind Gust multipliers to 0.448. Wind Resolution 0.72 Km/h
                             // If set to 1, set Cumulus Wind Speed and Wind Gust multipliers to 0.224. Wind Resolution 0.36 Km/h
                             // WARNING !!! Setting this variable to 1 allows a better wind speed and gust resolution,
                             // but also limits both of them, to a maximum reading of just 91.8 Km/h
                             // If set to 0, system uses Standard Davis 1 mph wind resolution.
   

// --------------------------------------------------------------------------------------
//   Define use of Wind Gust Spike prevention routines (mostly for FO anemometers)
// --------------------------------------------------------------------------------------
#define WindSpikeControl 1   // 0= Disable, 1= Enable method 1, 2= Enable method 2


// --------------------------------------------------------------------------------------
//   Define the source of your main outside sensors
// --------------------------------------------------------------------------------------
// ---- If you have all the sensors connected to only one TX board, always select Unit 0 as source
// ---- Define the source of your main Temperature / Humidity sensor
#define TH_OutUnit       0   // 0 for Temp/Hum sensor connected to TX_Unit 0, 1 for Temp/Hum sensor connected to TX_Unit 1
// ---- Define the source of your Main Wind sensor
#define WIND_OutUnit     0   // 0 for Wind instruments connected to TX_Unit 0, 1 for TX_Unit 1 
// ---- Define the source of your main Rain Gauge
#define RAIN_OutUnit     0   // 0 for Rain Gauge connected to TX_Unit 0, 1 for TX_Unit 1, 3 for Auriol RF Rain Gauge
// ---- Define the source of your main Solar / UV sensores
#define SRUV_OutUnit     9   // 0 for Solar Rad / UV sensors connected to TX_Unit 0, 1 for TX_Unit1, 9 for not used
// ---- Define installed Solar / UV Sensors
#define Solar_Sensor     1   // 0 for not present; 1 for present
#define UV_Sensor        1   // 0 for not present; 1 for present
#define UV_Transmission 10   // UV Transmission percentage of UV sensor cover material

// --------------------------------------------------------------------------------------
//   Extra Sensors Settings and Mapping
// --------------------------------------------------------------------------------------
// ---- Define the source and sensor number of each of the seven extra sensors, insert 9 if not used.
// ---- Source 0 (up to 3) means TX unit0, 1 means TX unit1... (sensor type SHT21 or HTU21D is number 0, sensor type SHT1x or DHT22 is number 1)
// ---- Source 6 is for OneWire sensors
// ---- Source 7 is for BIOS Sensor (Only Temp is get)
// ---- Source 8 is for Dust Density sensor. Sensor 0 is Temperature / Humidity, 1 is Dust Density / AQI
// ---- First field = Sensor source, Second field = Sensor number (0 or 1 for TX units) 
// ---- Example:
// ----                          ES0   ES1   ES2   ES3   ES4   ES5   ES6     
//#define ExtraSensors_Source { {0,1},{1,1},{9,9},{6,3},{9,9},{9,9},{9,9} }
//               {0,1} - First extra sensor (ES0), will be sensor 1 from TX unit0
//               {1,1} - Second extra sensor (ES1), will be sensor 1 from TX unit1
//               {9,9} - Third extra sensor (ES2), not used - not mapped
//               {6,3} - Fourth extra sensor (ES3), will be OneWire sensor number 3 (OneWire sensors are numbered from 0 to 3)
//
//-----                        ES0   ES1   ES2   ES3   ES4   ES5   ES6     
#define ExtraSensors_Source { {9,9},{9,9},{9,9},{9,9},{9,9},{9,9},{9,9} }

// ---- Define personalized names for each Extra sensor. Attention, maximum 8 chars
#define ExtraSensor1_Name "SENSOR 0"
#define ExtraSensor2_Name "SENSOR 1"
#define ExtraSensor3_Name "SENSOR 2"
#define ExtraSensor4_Name "SENSOR 3"
#define ExtraSensor5_Name "SENSOR 4"
#define ExtraSensor6_Name "SENSOR 5"
#define ExtraSensor7_Name "Dust/AQI"


// --------------------------------------------------------------------------------------
//   BIOS soil moisture sensor settings
// --------------------------------------------------------------------------------------
// ---- Please use the included BIOS_ID_Scanner sketch to find you BIOS Device ID
#define BiosSensor_ID 0xE   // Device ID in HEX format, or 0 not used

// --------------------------------------------------------------------------------------
//   Soil / Leaf Interface Settings and Sensors Mapping
//   (The mapping logic is the same than used with the Extra Sensors)
// --------------------------------------------------------------------------------------
// 0 = Soil Leaf Interface not used
// 1 = Soil Leaf Interface connected to a TX unit
#define SoilLeaf_Interface  0   // 0, 1, 

// ---- For Soil & Leaf data from SoilLeaf_Interface wired to a TX unit, use TX Unit number as source 
// ---- For BIOS Soil Temp / Moisture use 7 as source
// ---- To disable use 9 in both fields
//                                 S1    S2    S3    S4
#define SoilTempSensors_Source  { {9,9},{9,9},{9,9},{9,9} }
#define LeafTempSensors_Source  { {9,9},{9,9},{9,9},{9,9} }
#define SoilMoistSensors_Source { {9,9},{9,9},{9,9},{9,9} }
#define LeafWetSensors_Source   { {9,9},{9,9},{9,9},{9,9} }

// ---- Define personalized names for each Soil and Leaf sensor. Attention, maximum 8 chars
#define SoilSensor1_Name "Solo Frt"
#define SoilSensor2_Name "-"
#define SoilSensor3_Name "-"
#define SoilSensor4_Name "LagoAgua"
#define LeafSensor1_Name "Folhas  "
#define LeafSensor2_Name "1"
#define LeafSensor3_Name "2"
#define LeafSensor4_Name "4"

// Define VWC calculation method
// Method 1 applies only for VH400 soil moisture sensor
//
// METHOD 1 - Conversion from voltage to VWC (volumetric water content) is done using the piecewise regressions provided by the manufacturer 
// at http://www.vegetronix.com/Products/VH400/VH400-Piecewise-Curve.phtml 
//
// METHOD 2 - Used for any sensor which have a linear output between voltage and VWC (0V=0VWC, maxV=100VWC) .

#define VWC_CalcMethod 1

// Max and Min output voltage of the analog sensors connected to Soil / Leaf Interface
// Default value for Decagon Devices LWS Leaf Wetness Sensor (5V power): Max. Output Voltage - 1400mV (max wetness), Min Output Voltage - 530mV (dry)


//                                                  ADC1  ADC2  ADC3  ADC4  
const unsigned int AnalogSensor_MaxVoltOut[4]   = { 3000, 1395, 5000, 5000 };    // Values in miliVolts
const unsigned int AnalogSensor_MinVoltOut[4]   = {    0,  530,    0,    0 };


// --------------------------------------------------------------------------------------
//   Broadacasting settings for Wireless Display Units
// --------------------------------------------------------------------------------------
#define Relay_Data       1   // 0= Disables Data Relay, 1= Enables Data Relay


// --------------------------------------------------------------------------------------
//   Davis compatible Data Logger Settings
// --------------------------------------------------------------------------------------
#define Logger_Enable    1   // 0= Disable 1= Enable
byte ARCHIVE_PERIOD  =   5;  // Default Archive Period in Minutes (Usable values: 1, 5, 10, 15, 30)


// --------------------------------------------------------------------------------------
//   Easyweather format data Output 
// --------------------------------------------------------------------------------------
#define Easyweather_Out  0   // 0= Disable (defaut) 1= Enable


// --------------------------------------------------------------------------------------
//   Internet Settings 
// --------------------------------------------------------------------------------------
#define Enable_Internet     1                        // 1= Enable Internet connection, 0= Disable

#define SSID        "ASUS"                        // Write here your WiFi SSID 
#define PASSWORD    "************"                        // Write here your WiFi password

#define Enable_NTP          1                        // 1= Enable Sync time with NTP servers, 0= Disable
// NTP Servers:
#define timeServer "80.96.196.58"                    // timp.mcsi.ro
//#define timeServer "193.79.237.14"                 // ntp1.nl.net NTP server

#define Enable_WUupload     1                        // 1= Enable upload to Wunderground,     0= Disable
#define WUupload_period     3                        // Period in minutes between uploads to WU (avoid use less than 3 minutes) 
#define WUupload_InTemp     0                        // 1= Enable upload of Inside Temperature / Humidity, 0= Disable

// ---- Wunderground Personal Data
#define WUNDERGROUND_STATION_ID "INORTHWA13"            // Weather Underground station ID
#define WUNDERGROUND_PWD        "********"            // Weather Underground password


// --------------------------------------------------------------------------------------
//   Enable / Disable GPIO routines - General Purpose Input / Output ports
// --------------------------------------------------------------------------------------
#define UseGPIO  0   // 0=Disable, 1= Enable


// --------------------------------------------------------------------------------------
//   Test Mode : Never run a live system in test mode 
// --------------------------------------------------------------------------------------
#define TestMode    false    // false= Normal working mode, true= Test mode only (no logger, no usb connection)


// --------------------------------------------------------------------------------------
//   Hardware settings 
// --------------------------------------------------------------------------------------

// ---- Define LCD I2C address 
// Only change this if your LCD don't display any data. I2C_Scanner utility may help you to find the address of your LCD display
// Default address will work most of the times!
#define LCD_I2C_Address 0x27   


// --------------------------------------------------------------------------------------
//   SHT31 I2C Address - Default address will work most of the times!
// --------------------------------------------------------------------------------------
#define SHT31_address 0x44       // Default value is 0x44, but it can be changed to 0x45


// --------------------------------------------------------------------------------------
//   Presure Sensor Address (no need to change)
// --------------------------------------------------------------------------------------
//#define BMP085_ADDRESS 0x77    // I2C address of BMP085 or BMP180


// --------------------------------------------------------------------------------------
//   Debug helper 
// --------------------------------------------------------------------------------------
//#define PRINT_DEBUG_NTP_UPDATE    // Prints to serial monitor messages related to sync time with NTP server
//#define PRINT_DEBUG_WU_UPLOAD     // Prints to serial monitor messages related to Weather Underground upload.
//#define PRINT_DEBUG_AURIOL
//#define PRINT_DEBUG_BIOS

// ---------------------------------------------------------------------------------------------------
//     End of user configurable options
// ---------------------------------------------------------------------------------------------------