<![CDATA[WeatherDuino Forum - AuriolDuino - Info, FAQ's and News]]> https://www.meteocercal.info/forum/ Wed, 24 Jun 2026 23:15:30 +0000 MyBB <![CDATA[The AuriolDuino system was merged into the WeatherDuino Pro2 system]]> https://www.meteocercal.info/forum/Thread-The-AuriolDuino-system-was-merged-into-the-WeatherDuino-Pro2-system Thu, 17 Mar 2016 19:09:08 +0000 werk_ag]]> https://www.meteocercal.info/forum/Thread-The-AuriolDuino-system-was-merged-into-the-WeatherDuino-Pro2-system
The AuriolDuino system was merged into the WeatherDuino Pro2 system.

From now on, owners of Auriol weather stations (and compatibles) can also benefit from all the advantages offered by the WeatherDuino Pro2 system:

- Davis Vantage emulation
- Hardware data logger
- Direct connection to all weather software which support a Davis Vantage weather station (Cumulus1 or Cumulus MX is recommended)
- And many others...

- For all the weather stations mentioned above, all that is needed is a receiver unit based in a WeatherDuino Pro2 RX board. For those that will prefer a fully assembled and tested receiver unit, it is available too.


[Image: WeatherDuinoPro2_RXv600_assembled.jpg]

Later if you decide to upgrade your weather station to a full WeatherDuino Pro2 system, which supports a wide range of types and brands of weather instruments, you can continue to use the same receiver unit.]]>
The AuriolDuino system was merged into the WeatherDuino Pro2 system.

From now on, owners of Auriol weather stations (and compatibles) can also benefit from all the advantages offered by the WeatherDuino Pro2 system:

- Davis Vantage emulation
- Hardware data logger
- Direct connection to all weather software which support a Davis Vantage weather station (Cumulus1 or Cumulus MX is recommended)
- And many others...

- For all the weather stations mentioned above, all that is needed is a receiver unit based in a WeatherDuino Pro2 RX board. For those that will prefer a fully assembled and tested receiver unit, it is available too.


[Image: WeatherDuinoPro2_RXv600_assembled.jpg]

Later if you decide to upgrade your weather station to a full WeatherDuino Pro2 system, which supports a wide range of types and brands of weather instruments, you can continue to use the same receiver unit.]]> <![CDATA[EasyWeaher RS232 Logger]]> https://www.meteocercal.info/forum/Thread-EasyWeaher-RS232-Logger Wed, 04 Jun 2014 13:12:46 +0100 werk_ag]]> https://www.meteocercal.info/forum/Thread-EasyWeaher-RS232-Logger The AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.


EasyWeather RS232 Logger is a new software tool, developed by our member CT2IUB @ meteoestarreja, specially to be used with the AuriolDuino system.

It is intended to replace the use of the Elmita RS232 Data Logger with many benefits:

- It auto cleans the easyweather.dat file at defined intervals (1h, 12h or 24h). No more concerns about the growing size of the easyweather.dat file.
- Before you start Cumulus you can see incomming data from your Weather Station.
- It remembers your configuration options. Easy upgrades.
- Was been tested from months. Rock solid stability.

The "How to use with Cumulus" tutorials will be updated on the next days.

To get this great tool, please visit the download page.]]> The AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.


EasyWeather RS232 Logger is a new software tool, developed by our member CT2IUB @ meteoestarreja, specially to be used with the AuriolDuino system.

It is intended to replace the use of the Elmita RS232 Data Logger with many benefits:

- It auto cleans the easyweather.dat file at defined intervals (1h, 12h or 24h). No more concerns about the growing size of the easyweather.dat file.
- Before you start Cumulus you can see incomming data from your Weather Station.
- It remembers your configuration options. Easy upgrades.
- Was been tested from months. Rock solid stability.

The "How to use with Cumulus" tutorials will be updated on the next days.

To get this great tool, please visit the download page.]]> <![CDATA[How to use with Cumulus]]> https://www.meteocercal.info/forum/Thread-How-to-use-with-Cumulus Sat, 19 Apr 2014 03:13:15 +0100 werk_ag]]> https://www.meteocercal.info/forum/Thread-How-to-use-with-Cumulus The AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.



[Image: howtocumulos_image001.jpg]

- Install Easyweather_RS232_Logger (freeware)
http://www.meteoestarreja.info/logger.php/

1) Open Easyweather_RS232_Logger (this data logger was been specially designed to the AuriolDuino system)
2) Go to Config and there…
4) Click on COM Ports and configure your Arduino COM Port and Baud rate
3) Click on File Location and configure location for your easyweather.dat file
4) Click on Reset Interval and select interval for auto clean the easywaether.dat file (1h, 12h or 24h)
4) Check if you need to configure some other setting
6) It’s done! Start logging by clicking on the large Red Button on top right (Green when logging)
7) Click on Menu View and select / deselect active info windows.

[Image: EW_RS232_logger_02.JPG]


-Install Cumulus software (its free, but if you like it, please donate to Cumulus author)
http://sandaysoft.com/downloads

1) Open Cumulus
2) Click on Configuration
3) Click on Station
4) Choose in Station Type: EasyWeather (using dat file)
5) In Settings click on Calculate Dew Point and Calculate Wind Chill (optional)
6) EasyWeather Interval (choose anything below 0.5, I’m using 0.01)
7) In EasyWeather.dat, locate the easyweater.dat that you created earlier \Programs\Elmita Software\RS232 Data Logger\LOGS and click on it. OK.
8) Click on OK!

[Image: howtocumulos_image003.jpg]

Wait a few seconds and you should start receiving the weather data on your computer.

You must keep Easyweather_RS232_Logger always logging to Cumulus receive data.

This tutorial is only need to do once (when you install Cumulus and Easyweather_RS232_Logger), after the initial setup, when you want Cumulus to receive weather data (even if you restart or turn off the computer), it’s only needed to open Easyweather_RS232_Logger "start logging" and open Cumulus.

Cumulus update when the Arduino receives new weather data. Usually takes 31seconds for Wind, +-2minutes for Temperature/Humidity and 37 seconds for Rain.

I recommend waiting at least 2 minutes to start Cumulus, after clicking "start logging". If you open Cumulus right after "start logging" it will appear zeros in Temperature or Humidity or etc... this happens because the Arduino still didn’t receive all weather packages, so it will mess up your Cumulus statistics.
.zip AuriolDuino_RX_Use_Cumulus.zip Size: 213,41 KB  Downloads: 584
]]> The AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.



[Image: howtocumulos_image001.jpg]

- Install Easyweather_RS232_Logger (freeware)
http://www.meteoestarreja.info/logger.php/

1) Open Easyweather_RS232_Logger (this data logger was been specially designed to the AuriolDuino system)
2) Go to Config and there…
4) Click on COM Ports and configure your Arduino COM Port and Baud rate
3) Click on File Location and configure location for your easyweather.dat file
4) Click on Reset Interval and select interval for auto clean the easywaether.dat file (1h, 12h or 24h)
4) Check if you need to configure some other setting
6) It’s done! Start logging by clicking on the large Red Button on top right (Green when logging)
7) Click on Menu View and select / deselect active info windows.

[Image: EW_RS232_logger_02.JPG]


-Install Cumulus software (its free, but if you like it, please donate to Cumulus author)
http://sandaysoft.com/downloads

1) Open Cumulus
2) Click on Configuration
3) Click on Station
4) Choose in Station Type: EasyWeather (using dat file)
5) In Settings click on Calculate Dew Point and Calculate Wind Chill (optional)
6) EasyWeather Interval (choose anything below 0.5, I’m using 0.01)
7) In EasyWeather.dat, locate the easyweater.dat that you created earlier \Programs\Elmita Software\RS232 Data Logger\LOGS and click on it. OK.
8) Click on OK!

[Image: howtocumulos_image003.jpg]

Wait a few seconds and you should start receiving the weather data on your computer.

You must keep Easyweather_RS232_Logger always logging to Cumulus receive data.

This tutorial is only need to do once (when you install Cumulus and Easyweather_RS232_Logger), after the initial setup, when you want Cumulus to receive weather data (even if you restart or turn off the computer), it’s only needed to open Easyweather_RS232_Logger "start logging" and open Cumulus.

Cumulus update when the Arduino receives new weather data. Usually takes 31seconds for Wind, +-2minutes for Temperature/Humidity and 37 seconds for Rain.

I recommend waiting at least 2 minutes to start Cumulus, after clicking "start logging". If you open Cumulus right after "start logging" it will appear zeros in Temperature or Humidity or etc... this happens because the Arduino still didn’t receive all weather packages, so it will mess up your Cumulus statistics.
.zip AuriolDuino_RX_Use_Cumulus.zip Size: 213,41 KB  Downloads: 584
]]> <![CDATA[AuriolDuino system FAQ]]> https://www.meteocercal.info/forum/Thread-AuriolDuino-system-FAQ Fri, 18 Apr 2014 14:37:54 +0100 werk_ag]]> https://www.meteocercal.info/forum/Thread-AuriolDuino-system-FAQ From March 2016, the AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.


AuriolDuino works with my weather station?
Actually it works with Auriol H13726, Ventus W155, Hama EWS 1500, Meteoscan w155 / w160, Alecto WS-3500 and Balance RF-WS100 weather stations.

Are the AuriolDuino System kits ready to use?
Yes. They are fully assembled and tested. You only need to install the required PC software (free) and you are ready to see, record ou upload to the internet your weather station data.

How it connects to my PC?
AuriolDuino connects to your PC via USB.

Is it compatible with any of the well know PC Weather Software?
Yes. You can use it with any software that can read the Easyweather file format. I recomend CUMULUS, one of the best and most used worldwide. To see a tuturiol about how to use it with Cumulus here.
]]> From March 2016, the AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.

The info below is outdated, and not apply to the WeatherDuino Pro2 system.


AuriolDuino works with my weather station?
Actually it works with Auriol H13726, Ventus W155, Hama EWS 1500, Meteoscan w155 / w160, Alecto WS-3500 and Balance RF-WS100 weather stations.

Are the AuriolDuino System kits ready to use?
Yes. They are fully assembled and tested. You only need to install the required PC software (free) and you are ready to see, record ou upload to the internet your weather station data.

How it connects to my PC?
AuriolDuino connects to your PC via USB.

Is it compatible with any of the well know PC Weather Software?
Yes. You can use it with any software that can read the Easyweather file format. I recomend CUMULUS, one of the best and most used worldwide. To see a tuturiol about how to use it with Cumulus here.
]]> <![CDATA[What is the AuriolDuino system?]]> https://www.meteocercal.info/forum/Thread-What-is-the-AuriolDuino-system Fri, 18 Apr 2014 05:35:02 +0100 werk_ag]]> https://www.meteocercal.info/forum/Thread-What-is-the-AuriolDuino-system From March 2016, the AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.


The AuriolDuino system is a combination of Arduino hardware and software, wich enables a owner of an Auriol H13726 Weather Station and compatibles*, to receive and decode all the data sent from the original external sensors to the base station.
It can be connected to a PC by USB, which enables you to view, store and even publish on the Internet your Weather Station data.

*Also suitable for the following Weather Stations: Ventus W155, Hama EWS 1500 / Meteoscan w155 w160 / Alecto WS-3500 / Balance RF-WS100

The AuriolDuino system was been designed to be used with Cumulus software, via Easyweather.dat data format, but if you have some knowledge of programming in Arduino environment, you can adapt the software to your own needs.

The AuriolDuino is a very flexible system. It can be built with more or less hardware parts, according to the way you want to use it. It can have an Real Time Clock, a 20x4 LCD display or even a color 1.8" TFT display. Support for all this optional hardware is included on the software.
Also, can be used in stand alone mode, and act like a second console to install on a different location from the original one.

Additionally, the AuriolDuino system includes some nice extra functions, aimed primarily at solving the main problem of this kind of Weather Stations, which lies in the unreliability of the data from the external temperature sensor, due to the fact that the original hardware does not have an effective Radiation Shield. You can solve this problem without even touching your original weather station hardware.
The AuriolDuino Receiver allows simultaneous reception of RF data sent by your original sensors, plus data sent by a specially designed TX board, where you can connect an extra Temperature / Humidity sensor, installed in a Radiation Shield, and positioned at the best location, in order to obtain data with better accuracy.

For more info about this, visit the AuriolDuino -> Hardware area.
]]> From March 2016, the AuriolDuino system was merged into the WeatherDuino Pro2 system.
For more info please click here.


The AuriolDuino system is a combination of Arduino hardware and software, wich enables a owner of an Auriol H13726 Weather Station and compatibles*, to receive and decode all the data sent from the original external sensors to the base station.
It can be connected to a PC by USB, which enables you to view, store and even publish on the Internet your Weather Station data.

*Also suitable for the following Weather Stations: Ventus W155, Hama EWS 1500 / Meteoscan w155 w160 / Alecto WS-3500 / Balance RF-WS100

The AuriolDuino system was been designed to be used with Cumulus software, via Easyweather.dat data format, but if you have some knowledge of programming in Arduino environment, you can adapt the software to your own needs.

The AuriolDuino is a very flexible system. It can be built with more or less hardware parts, according to the way you want to use it. It can have an Real Time Clock, a 20x4 LCD display or even a color 1.8" TFT display. Support for all this optional hardware is included on the software.
Also, can be used in stand alone mode, and act like a second console to install on a different location from the original one.

Additionally, the AuriolDuino system includes some nice extra functions, aimed primarily at solving the main problem of this kind of Weather Stations, which lies in the unreliability of the data from the external temperature sensor, due to the fact that the original hardware does not have an effective Radiation Shield. You can solve this problem without even touching your original weather station hardware.
The AuriolDuino Receiver allows simultaneous reception of RF data sent by your original sensors, plus data sent by a specially designed TX board, where you can connect an extra Temperature / Humidity sensor, installed in a Radiation Shield, and positioned at the best location, in order to obtain data with better accuracy.

For more info about this, visit the AuriolDuino -> Hardware area.
]]>