// --------------------------------------------------------------------------------------
//   User configurable options 
// --------------------------------------------------------------------------------------


// --------------------------------------------------------------------------------------
//   Define ID and TX unit number
// --------------------------------------------------------------------------------------
#define StationID  0xA1    // Must be equal to your RX Unit (Value from 0x00 to 0xFF)  
#define UnitID        0    // If you use only one TX unit define it as UnitID = 0
                           // For a second TX unit, define it as UnitID = 1

// --------------------------------------------------------------------------------------
//   Define type of Temperature / Humidity sensor used as Sensor 0 and / or Sensor 1
// --------------------------------------------------------------------------------------
#define TH_Sensor0  0      // [SENSOR 0] - 0 for SHT2x sensor, 1 for SHT31 sensor, 2 for HTU21 sensor, 9 for Not Used
#define TH_Sensor1  9      // [SENSOR 1] - 0 for SHT1x sensor, 1 for DHT22 sensor, 9 for Not Used


// --------------------------------------------------------------------------------------
//   Define which data this unit will send. 0 = Not send this data, 1= Send this data 
// --------------------------------------------------------------------------------------
#define ID0  1   // Temp/Hum Data 
#define ID1  0   // Not Used
#define ID2  1   // Wind data
#define ID3  1   // Rain data
#define ID4  1   // UV / SolRad data
#define ID5  1   // Hardware Status - System Temp, Battery Voltage etc
#define ID7  0   // Send Soil & Leaf Temperature Data
#define ID9  0   // Send Soil & Leaf Moisture / Wetness Data


// --------------------------------------------------------------------------------------
//   Define which Temp / Hum sensor controls the fan, and threshold values
// --------------------------------------------------------------------------------------
#define FanControlSensor  0      // 0 for Sensor 0, 1 for Sensor 1 (which sensor is used to control the RS Fan)
#define fanOn_HiTemp     40      // RS Fan turn on when outside temperature is >= than this value (ºC) 
#define fanOn_LowTemp     2      // RS Fan turn on when outside temperature is <= than this value (ºC) 
#define fanOn_LowWind     1      // RS Fan turn on when Wind Average is <= than this value (m/s)


// --------------------------------------------------------------------------------------
//   Define type of Wind Speed sensor. See below for allowed types
// --------------------------------------------------------------------------------------
/*
 --- Fine Offset Anemometers ---
 Use 1O for standard FO anemometers
 Use 11 for FO anemometer modified with 1 hall effect sensor

 --- Inspeed Anemometers ---
 Use 20 for Inspeed Vortex, digital 8 pulse revolution anemometer
 Use 21 for Inspeed Vortex, hall efect sensor
 Use 21 for Inspeed Vortex, read switch sensor
 
 --- Davis Anemometers ---
 Use 30 for Davis 6410 anemometer
 
 --- Novalynx Anemometers ---
 Use 40 for Novalynx, model 200-WS-02F

 --- Environmental Measurements Limited ---
 Use 50 for EML, model WSD1

 --- Didcot Instrument Company ---
 Use 60 for DIDCOT, model DWR205
*/
#define WSpeedSensor_Type 21             // SEE INFO ABOVE!!!


// --------------------------------------------------------------------------------------
//   Define type of Wind Direction sensor
// --------------------------------------------------------------------------------------
/*
 --- Fine Offset Wind Vane ---
 Use 1O for standard FO wind vane
 
 --- Inspeed Wind Vane ---
 Use 20 for Inspeed E-Vane 2
 
 --- Davis Wind Vane ---
 Use 30 for Davis 6410 wind vane
 
 --- Novalynx Wind Vane
 Use 40 for Novalynx, model 200-WS-02F
 
 --- Environmental Measurements Limited Wind Vane ---
 Use 50 for EML, model model WSD1
 
   --- Didcot Instrument Company ---
 Use 60 for DIDCOT, model DWD205
*/
#define WDirSensor_Type  20  // SEE INFO ABOVE!!!


// --------------------------------------------------------------------------------------
//          Inspeed Vane Calibration
//    Calibration values for Inspeed E-Vane 2
// --------------------------------------------------------------------------------------
#define WDir_min         60
#define WDir_max        990
#define WDir_offs         0


// --------------------------------------------------------------------------------------
//   Define Rain Gauge tip boucket value (mm)
// --------------------------------------------------------------------------------------
/*
  Use 0.300 for standard FineOfset rain gauges (Datasheet value = 0.2794)
  Use 0.200 for standard Davis rain gauges
*/  
#define COLLECTOR_TYPE  0.200  // Please note: Values must be in metric units. Max. resolution: 3 decimal digits
   

// --------------------------------------------------------------------------------------
//   Soil / Leaf Interface Enable Disable
// --------------------------------------------------------------------------------------
#define SoilLeaf_Interface     0   // 0 = Soil Leaf Interface not used, 1 = Enable Soil Leaf Interface
#define Number_AnalogSensors   0   // Up to 4 analog sensors


// --------------------------------------------------------------------------------------
//   Hardware settings 
// --------------------------------------------------------------------------------------
// SHT31 I2c Address
// Default address will work most of the times!
#define SHT31_address 0x44           // Default value is 0x44, but it can be changed to 0x45 

// --------------------------------------------------------------------------------------
//   Debug
// --------------------------------------------------------------------------------------
#define Debug_Enable      false
#define DebugID0          false
#define DebugID2          false
#define DebugID3          false
#define DebugID4          false
#define DebugID5          false
#define Easyweather_Test  false
#define Debug_SLinterface false


// ---------------------------------------------------------------------------------------------------
//     End of user configurable options
// ---------------------------------------------------------------------------------------------------