// --------------------------------------------------------------------------------------
//   User configurable options 
// --------------------------------------------------------------------------------------

#define Station_ID     0xA1   // Station_ID, use the same value in all TX units
#define Relay_ID       0xA3   // Relay_ID,   use the same value in all WD units

// --- Define Software Operation Mode
#define Work_Mode         0   // Mode 0= Davis VP2 Emulation Mode, Mode 1= EasyWeather Mode

// --- Define your Display type
// --- Chosing TFT automatically disables the data logger function (no memory for both)
#define DisplayType       1   // 0= TFT, 1= LCD 20x4, 2= LCD 16x2

// --- Define Backlight TimeOut
// --- With old RX boards, version <= 3.01 always set this value to 0
const byte  BackLight_Timeout = 15;   // Timeout for display backlight in minutes (1 to 255). 0 = Always ON 

// --- Define Display unit Formats --------------------------------------------
#define Date_Time_Format    0    // 0 for dd-mm-yyyy, 1 for yyyy/mm/dd
#define Temp_Display_Unit   0    // 0 for ºC, 1 for ºF
#define ATM_Display_Unit    0    // 0 for mBar, 1 for inHg
#define Rain_Display_Unit   0    // 0 for mm (no other options)
#define Wind_Display_Unit   0    // 0 for Km/h, 1 for mph, 2 for m/s, 3 for Knots

// --- Fine adjusts for Inside Temperature and Barometer
const int   TemperaturaInt_offset =    0;   // Inside Temperature Fine Adjust in Tenths of Degree (-4 = -0,4ºC) 
const float pressure_offset       =    0;   // Pressure Fine Adjust in mB

// --- Some Data from your Weather Station location
#define LATITUDE        0    // Put here your Station latitude in tenths of degrees North
#define LONGITUDE       0    // Put here your Station longitude in tenths of degrees (minus for West)
#define ELEVATION       0    // Put here your Station height above sea level in Meters

// --- Define Roll Over Hour for Meteorological Day
#define MeteoDay_HStart 0    // Use values from 0 to 23

// --- Define Wind Speed and Wind Gust resolution
#define VP2_WindRes     2    // If set to 2, set Cumulus Wind Speed and Wind Gust multipliers to 0.448. Wind Resolution 0.72 Km/h
                             // If set to 1, set Cumulus Wind Speed and Wind Gust multipliers to 0.224. Wind Resolution 0.36 Km/h
                             // WARNING !!! Setting this variable to 1 allows a better wind speed and gust resolution,
                             // but also limits both of them, to a maximum reading of just 91.8 Km/h
                             // This setting only have effect when the software is used in Davis VP2 emulation mode
                             // If set to 0, system uses Standard Davis 1 mph wind resolution.
   
// --- Define the type of your inside Temperature / Humidity Sensor
#define InsideTH_Sensor  0   // 0= DHT22, 1= HTU21D

// ---- Lets define the source or type of our main outside sensors
// ---- If you have all the sensors connected to only one TX board, always select Unit 0 as source
// ---- Define the source of your main Temperature / Humidity sensor
#define TH_OutUnit       0   // 0 for Temp/Hum sensor connected to TX_Unit 0, 1 for Temp/Hum sensor connected to TX_Unit 1
// --- Define your main outside Temperature / Humidity Sensor
#define MainOutTH_Sensor 1   // 0 for sensor type SHT21 or HTU21D, 1 for sensor type SHT1x or DHT22 
// ---- Define the source of your Main Wind sensor
#define WIND_OutUnit     0   // 0 for Wind instruments connected to TX_Unit 0, 1 for TX_Unit 1 
// ---- Define the source of your main Rain Gauge
#define RAIN_OutUnit     0   // 0 for Rain Gauge connected to TX_Unit 0, 1 for TX_Unit 1, 2 for Auriol RF Rain Gauge
// ---- Define the source of your main Solar / UV sensores
#define SRUV_OutUnit     9   // 0 for Solar Rad / UV sensors connected to TX_Unit 0, 1 for TX_Unit1, 9 for not used
// ---- Define installed Solar / UV Sensors
#define Solar_Sensor     1   // 0 for not present; 1 for present
#define UV_Sensor        1   // 0 for not present; 1 for present

// ---- Lets mapping our outside Extra Sensors
// ---- Define the source of each extra sensor, and if it is sensor 0 or 1. Insert 9 if not used
// Extra Sensor 1
#define Extra1_TXunit   9   // 0 for TX unit0, 1 for TX unit1, 2 for TX unit2
#define Extra1_Sensor   9   // 0 for sensor0 (type SHT21 or HTU21D), 1 for sensor1 (type SHT1x or DHT22) 
// Extra Sensor 2
#define Extra2_TXunit   9
#define Extra2_Sensor   9
// Extra Sensor 3
#define Extra3_TXunit   9
#define Extra3_Sensor   9
// Extra Sensor 4
#define Extra4_TXunit   9
#define Extra4_Sensor   9
// Extra Sensor 5
#define Extra5_TXunit   9
#define Extra5_Sensor   9

// ---- Broadacasting Data Settings
#define Relay_Data       1   // 0= Disables Data Relay, 1= Enables Data Relay

// ---- Data Logger Settings
#define Logger_Enable    1   // 0= Disable 1= Enable
byte ARCHIVE_PERIOD  =   5;  // Default Archive Period in Minutes (Usable values: 1, 5, 10, 15, 30, 60 or 120)

// ---- Define your RX board main version number
#define Board_Version    4   // ex: 4 for all RX boards v4.xx

// ---------------------------------------------------------------------------------------------------
//     End of user configurable options
// ---------------------------------------------------------------------------------------------------