Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

UV Sensor Debug
#1

Hi Everyone, I am currently building my setup and testing the UV sensors UVM30A and I get the message below when trying to compile, everything else is working perfectly. I am getting a voltage reading on the ADC pin of the nano, the debug works for the other sensors, any help appreciated, thanks, regards, Rob


Process_IDx:295:19: error: missing expression between '(' and ')'

#if (DEBUG_ID4)

^

exit status 1

missing expression between '(' and ')'
Reply
#2

Hi Rob,

Indeed there is an error on Process_IDx line 295

On line 295, just replace:

Code:
#if (DEBUG_ID4)

by

Code:
#ifdef DEBUG_ID4

Alternatively, you can download again the software package for your receiver, I already fixed the reported error.
Thank you, and sorry for this inconvenience.

Hope soon your station will have Solar Radiation and UV Index data too.

Rgs.
Werk_AG
Reply
#3

(08-03-2021, 19:31)Werk_AG Wrote:  Hi Rob,

Indeed there is an error on Process_IDx line 295

On line 295, just replace:
 
Code:
#if (DEBUG_ID4)

by
 
Code:
#ifdef DEBUG_ID4

Alternatively, you can download again the software package for your receiver, I already fixed the reported error.
Thank you, and sorry for this inconvenience.

Hope soon your station will have Solar Radiation and UV Index data too.

Rgs.
Werk_AG

Hi Werk_AG

Thanks for that, I did manage to locate that before reading your reply which I am quite pleased with as I am still a novice when it comes to code! I have changed it and the UV reading come up in the serial monitor but still not on the compact display/cumulus, I have the following settings in the Config file - 
 
Code:
// --------------------------------------------------------------------------------------
//    WeatherDuino Pro2 Universal TX AT328 - Version: 7.0_b003
//           Start of user configurable options
// --------------------------------------------------------------------------------------


// --------------------------------------------------------------------------------------
//   Define ID and TX unit number
// --------------------------------------------------------------------------------------
#define Station_ID  0xA1    // Must be equal to your RX Unit (Value from 0x00 to 0xFF)  
#define Unit_ID        0    // If you use only one TX unit define it as Unit_ID = 0
                            // For a second TX unit, define it as Unit_ID = 1

// --------------------------------------------------------------------------------------
//   Define type of Temperature / Humidity sensor used as Sensor 0 and / or Sensor 1
// --------------------------------------------------------------------------------------
#define TH_SENSOR0  1      // [SENSOR 0] - 0 for SHT2x sensor, 1 for SHT31 sensor, 2 for HTU21 sensor, 9 for Not Used
#define TH_SENSOR1  9      // [SENSOR 1] - 0 for SHT1x sensor, 1 for DHT22 sensor, 9 for Not Used


// --------------------------------------------------------------------------------------
//   Define which Temp / Hum sensor controls the RS fan, and threshold values
// --------------------------------------------------------------------------------------
#define FANCONTROL_SENSOR  0      // 0 for Sensor 0, 1 for Sensor 1 (which sensor is used to control the RS Fan)
const int fanOn_HiTemp  =  19;     // RS Fan turn on when outside temperature is >= than this value (ºC)
const int fanOn_LowTemp =  2;     // RS Fan turn on when outside temperature is <= than this value (ºC)
const int fanOn_LowWind =  1;     // RS Fan turn on when Wind Average is <= than this value (m/s)


// --------------------------------------------------------------------------------------
//   Define type of Wind Speed sensor. See below for allowed types
// --------------------------------------------------------------------------------------
/*
--- Fine Offset Anemometers ---
Use 1O for standard FO anemometers
Use 11 for FO anemometer modified with 1 hall effect sensor

--- Inspeed Anemometers ---
Use 20 for Inspeed Vortex, digital 8 pulse revolution anemometer
Use 21 for Inspeed Vortex, hall efect sensor
Use 22 for Inspeed Vortex, read switch sensor

--- Davis Anemometers ---
Use 30 for Davis 6410, 7911 anemometer

--- Novalynx Anemometers ---
Use 40 for Novalynx, model 200-WS-02F

--- Environmental Measurements Limited ---
Use 50 for EML, model WSD1

--- Didcot Instrument Company ---
Use 60 for DIDCOT, model DWR205

--- Vector Instruments ---
Use 70 for Vector Instruments model A100LK
Use 71 for Vector Instruments model A100L2
Use 72 for Vector Instruments model A100R
*/
#define WINDSPEED_SENSORTYPE 10             // SEE INFO ABOVE!!!


// --------------------------------------------------------------------------------------
//   Define type of Wind Direction sensor
// --------------------------------------------------------------------------------------
/*
--- Fine Offset Wind Vane ---
Use 1O for standard FO wind vane

--- Analogue Wind Vanes ---
Use 20 for any 5V analogue wind vane. See bellow for a list of tested models

- Inspeed E-Vane 2
- Davis 6410
- Novalynx, model 200-WS-02F
- Environmental Measurements Limited, model model WSD1
- DIDCOT, model DWD205
- Almost all 5V analogue wind vanes will work

*/
#define WINDDIR_SENSORTYPE  10  // SEE INFO ABOVE!!!


// --------------------------------------------------------------------------------------
//          Analogue Vane Offset Calibration
// --------------------------------------------------------------------------------------
const int WDir_offs  = 0;   // Usually there is no need to change default value (zero)


// --------------------------------------------------------------------------------------
//   Define Rain Gauge tip boucket value (mm)
// --------------------------------------------------------------------------------------
/*
  Use 0.280 for standard FineOfset rain gauges (Datasheet value = 0.2794)
  Use 0.200 for standard metric Davis rain gauges
  Use 0.254 for standard imperial Davis rain gauges
*/  
#define COLLECTOR_TYPE  0.280  // Please note: Values must be in metric units. Max. resolution: 3 decimal digits
  

// --------------------------------------------------------------------------------------
//   Define type of UV Sensor
// --------------------------------------------------------------------------------------
#define UV_SENSOR  0      // 0= UVM-30A, 1= VEML6075, 9= Not used


// --------------------------------------------------------------------------------------
//   Soil / Leaf Interface Enable Disable
// --------------------------------------------------------------------------------------
#define SOILLEAF_INTERFACE        0    // 0 = Soil Leaf Interface not used, 1 = Enable Soil Leaf Interface
const byte Number_AnalogSensors = 2;   // Up to 4 analog sensors


// --------------------------------------------------------------------------------------
//   Define which data this unit will send. 0 = Not send this data, 1= Send this data
// --------------------------------------------------------------------------------------
#define ID0  1   // Temp/Hum Data
#define ID1  0   // Not Used
#define ID2  1   // Wind data
#define ID3  1   // Rain data
#define ID4  1   // SolRad / UV data
#define ID5  1   // Hardware Status - System Temp, Battery Voltage etc
#define ID7  0   // Send Soil & Leaf Temperature Data
#define ID9  0   // Send Soil & Leaf Moisture / Wetness Data


// --------------------------------------------------------------------------------------
//   VBat voltage fine tune (values in Volt, positive or negative)
// --------------------------------------------------------------------------------------
#define VBAT_OFFSET    0.0                  //


// *************************************************************************************
//     Hardware Settings
// *************************************************************************************
// Define if the TMP36 sensor is instaled
#define USE_TMP36       1          // 0= Not Instaled, 1= Intalled


// --------------------------------------------------------------------------------------
//   SHT31 I2C Address - Default address will work most of the times!
// --------------------------------------------------------------------------------------
#define SHT31_ADDRESS 0x44           // Default value is 0x44, but it can be changed to 0x45


// --------------------------------------------------------------------------------------
//   Debug
// --------------------------------------------------------------------------------------
//#define ENABLE_DEBUG
//#define DEBUG_ID0  
//#define DEBUG_ID2  
//#define DEBUG_ID3  
//#define DEBUG_ID4  
//#define DEBUG_ID5  
//#define DEBUG_SLINTERFACE
//#define EASYWEATHER_TEST  


// ---------------------------------------------------------------------------------------------------
//     End of user configurable options
// ---------------------------------------------------------------------------------------------------
 Thanks
Regards
Rob
Reply
#4

Hi again

I have sorted it out now, I forgot to change the settings in the receiver config file  Big Grin Sleepy

Thanks 
Regards
​​​​​​​Rob
Reply
#5

I just can say that you are going pretty, pretty well. Like
Those initial "troubles" are normal until you get familiar to the several WeatherDuino config options.
For any doubt, I will be here.

Rgs.
Werk_AG
Reply




Users browsing this thread: 1 Guest(s)